Hi We have an application where we what to read i2c sensor data over the air to an iPhone. We've taken ble_app_uart_S130 project and grafted in some twi_hardware code. There...
I am interested in the S130 ability to hold 3 central -> peripheral links over BLE, and am looking for some evidence that this has been accomplished with extremely low-power...
I'm trying to implement channel scanning in our nrf24lu1p based USB dongle.
I'm following the specs and basically loop though each channel ;
loop
stop listening
set...
Hi,
I am using the NRF8001 in UART mode and attempting to bond with my android device (Lollipop 5.0 Nexus 6).
i am using the nordic arduino sdk which is found here:...
Hi, I'm using the nRF8001 in an application that requires security so bonds to the remote client/central. My device supports firmware upgrades that may involve new nRF8001...
Hello.
Initially when reading the Gazell documentation I didn't think it'd be a problem but now in Keil seeing this has introduced some doubt whether it's a thing:
...
Hi guys,
I have MQTT v5 up and running but I am currently trying to implement one-way TLS then mutual TLS once it's completed. I am not too sure what I am doing wrong but...
Hi:
My environment is: Windows laptop, nRF52 DK (Peripheral), nRF52840 Dongle, Mobile Central (iOS and Android), and Wireshark nRF Sniffer for Bluetooth.
Peripheral sends...
Hello all,
I have problem with flashing the code. It gives me memory protection error.
Steps I followed for creating firmware and flashing:
1- I took a sample from nrf...
I'm working on a product prototype using the nrf5340 audio dk to send audio via Auracast. We started from the nrf5340_audio application, as it implements a large fraction...
While testing UART communication between a Seeed XIAO board and the nRF9151 DK, I connected the following pins: - XIAO 3.3 V → DK VDD - XIAO GND → DK GND - XIAO TX → DK RX...
Hello,
In the nRF52840 datasheet, some pins are explicitly marked as “low frequency I/O only.” However, I couldn’t find any similar indication in the nRF54L10 datasheet...
Hi everyone,
I’m testing a custom nRF54L15 board with BLE, but it gets stuck inside bt_enable() . To debug the issue, I checked whether my 32 MHz external crystal (HFXO...
Hi, I want to use the external flash on nRF9151-DK (gd25wb256). Having set all the necessary files (prj.conf, nrf9151dk_nrf9151_ns.overlay) and some parameters in the main...
Hi Nordic Community,
I'm testing NFC functionality on the nRF52840 DK development kit using the record_text sample from nRF Connect SDK v2.9.1 (which includes Zephyr OS...
Recently, when using the ncs v2.9.0 SDK, I found that the definitions for some interfaces could not be found. For instance, nrf_radio_packet_conf_t (it cannot be found even...
I am currently working with the Channel Sounding sample on the nRF54L15 DK boards and using Nordic’s multiple-antenna support as described here: docs.nordicsemi.com/.../channel_sounding...
Hi, I’m working on an nRF52840DK-based Bluetooth Mesh project derived from the Chat sample on nRF connect SDK extension for VS Code.
The setup involves three types of nodes...
What antenna type is required for FCC ID reuse in an end product? Can only the Ethertronics P822601 be used without filing for an FCC permissive change? The FCC grant for...
As you can see here it mentions the ble version is 5.2 but if we click through and get into its datasheet the ble version is 5.0 . And also in the datasheet of nrf52832 no...
