Hello.
Initially when reading the Gazell documentation I didn't think it'd be a problem but now in Keil seeing this has introduced some doubt whether it's a thing:
...
We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hello, I am designing a hardware based on nrf52832 module MDBT42Q. I need to know about theSWD programmer connections. I exposed pin swdio, swdclk, vcc, gnd to a 4-pin header...
Hi,
I'm currently developing a certain product having limitted power source (about avg. current < 100 uA ).
main SoC is nRF52840, and SDK version is nRF5 SDK 17.
...
Hi,
I have an inter-processor communication using I2C working well with the NRF51, the NRF51 performs a read as a master from the other micro ( slave ) which returns a packet...
Hi,
Setup : nRF SDK 1.9.0 and nRF52840, with an External flash MX25L series. Using SPI (not QSPI)
I'm noticing a huge difference between speed of file upload over SMP...
We made two set of firmwares, one with radio test controllable through CLI RTT and other with DTM. Problem with DTM firmware is our end product don't have UART or extra GPIOs...
Hi,
I have a very simple example which just enables the SPI flash on the nrf9160 and then tries to mount littlefs on it. Unfortunately, it doesn't seem to be working...
Hi,
I have successfully flashed the Zephyr Bluetooth: Peripheral HT sample to my nRF52833 DK.
I would like to change the service used for temperature indications from...
Hi,
Where can I find an abbreviations list and explanation what the meaning is for all abbreviations Nordic use?
nRF, SDC, NCS, SDK, PDK, DK, QDID
What is the difference...
Hi all，
I am developing the door lock using matter. The SDK uses ncs2.1.0, nrf/samples/matter/lock, and I want to test the connection to google home app on Android phone...
Development Environment: VS Code on Windows 10, SDK: 2.0.0, HW: nRF5340 Development Kit I am trying to perform just a network core update on the nRF5340 DK based off of the...
Hi,
I was trying to send a long buffer using I2C. The buffer size that I want to send is 2048 bytes. Below is the buffer that I want to write
But when I check on...
Hello
I am testing the nrf_GFX example with ST7735
but the example has a ST7735 128x 160 and i have St7735 80 x 160, I Change de dimentions in sdk_config.h
in the...
Hi, I'm a beginner for nrf52840 development.
As I know the ARM core operates on 64MHz clock.
So I think there is 64 MHz clock in this board.
My question is the...
Hello everyone,
I accidentaly flash the Dk when the power profiler kit was plug on it, so now the led are Always off on the PPK, to fix this I have to flash the PPK but...
hi support team,
i have one ticket about 53832 hardware problem that is resolved:
devzone.nordicsemi.com/.../52832-p0-25-and-p0-26-problem ,
Surprisingly i found out...
