Hi,
I am using the NRF8001 in UART mode and attempting to bond with my android device (Lollipop 5.0 Nexus 6).
i am using the nordic arduino sdk which is found here:...
Hi, I'm using the nRF8001 in an application that requires security so bonds to the remote client/central. My device supports firmware upgrades that may involve new nRF8001...
Hello.
Initially when reading the Gazell documentation I didn't think it'd be a problem but now in Keil seeing this has introduced some doubt whether it's a thing:
...
We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hi,
I am still investigating this but, I think it is best that we discuss it on this forum.
I am using SDK 16.0.0, nRF52840, secure_bootloader_usb on a custom board. The...
I just received notification from Onsemi that the ESD protection chip (CM1402-03CP) that I am using between my SIM card connector and nRF91 is obsolete. This is the same chip...
After upgrading nRF Connect SDK to v2.1.0 I noticed that my modified version of connectivity bridge (when running on thingy:91 nrf52840), stops working 30-60 seconds after...
Hi I'm developing a board to isolate external GPIO signals from a Nordic nRF52832 (Isolated input from 5VDC to 25VDC). For this I am using a circuit with the PC817 optoisolator...
Hi, I have similar error on this thread:
I cloned current latest releases of Android-nRF-Toolbox(3.1.3), Android ble library(2.5.1), and Android common library(1.0.27...
Hi everyone,
I'm using an nRF 5340-DK and want to update the application core firmware by using the nRF secure immutable bootloader. The bootloader and the network core...
Hi
I am currently running and adjusting the zephyr echo_bot uart sample on my nrf9160 DK. Currently , the sample makes use of UART0 to send a receive information which I...
I'm trying to connect a Thingy91 to the nRF cloud using just in time provisioning. I'm using MoSh. Here is the error:
mosh:~$ cloud_rest jitp Performing JITP... JITP device...
Hello,
When I change the optimization for a project to NO_OPTIMIZATIONS or DEBUG_OPTIMIZATIONS in the configuration (prj.conf), I always go in the hard fault handler ...
Hello,
i have a Nordic nRF52840DK and a Qorvo DWS3000 combination. I´m using SDK7.0.2, Segger Embedded Studio 5.10a and J-Link 7.58b.
I want to combine the ble_app_uart_c_pca10056_s140...
Can you please explain how NRFX_SPIM_FLAG_RX_POSTINC works? My data keeps always being loaded into the same address. Here is my code snippet:
uint8_t tx_buffer_MAG[1]...
I am developing a product with nRF52832 in which we need to use the COMP module. We need to route the RESULT signal directly to the RX input of the UART, or to an output of...
