Hi,
I'm using redbearlab's nrf51822 board. It is a arduino compatible board and hence it is using 0,1 (mapped to 9 and 11 for nrf51822). How do I make printf print to this...
An external PA/LNA is used to extend range of nRF51822, and S110 is used for BLE, How to switch between PA and LNA? and how to disable PA/LNA when there isn't transceiving...
Hi...
Can anybody help me to run ble_peripheral example (ble_app_hrs for S130). I have build and load the code successfully but cant see the advertisement. But while debugging...
I am working with the nRF8001, and I'd like to create a services.h file that will let me broadcast battery level and as well as allow temperature to be read by a peer.
...
Hi We have an application where we what to read i2c sensor data over the air to an iPhone. We've taken ble_app_uart_S130 project and grafted in some twi_hardware code. There...
I am interested in the S130 ability to hold 3 central -> peripheral links over BLE, and am looking for some evidence that this has been accomplished with extremely low-power...
I'm trying to implement channel scanning in our nrf24lu1p based USB dongle.
I'm following the specs and basically loop though each channel ;
loop
stop listening
set...
Hi,
In the SDK 17.1.0 release note (downloaded from https://www.nordicsemi.com/Products/Development-software/nRF5-SDK/Download?lang=en#infotabs ), the verification GCC compiler...
I'm trying to create a Zephyr Shell command where I can write a certificate to the modem. Putting the certificate in the command line doesn't work, so I was going to use the...
Hi
I'm using nRF52805 to realize the DFU function using the buttonless_dfu example project. I follow the instruction of this and use commands in this discussion .
After...
Hi I have an question about use ZB_ZCL_DECLARE_POWER_CONFIG_ATTRIB_LIST macro in case when only one battery used.
I'm trying to declare Power Configuration like this
...
Hi. I don't believe this question would be strictly be considered a duplicate. I have seen posts discussing the same issue I'm having, but resolutions don't appear to solve...
In order to use this application in nRF Connect for Desktop, I have just purchased an nRF52-DK. As I'm using macOS, I believe that I'm affected by the 64 byte limit and need...
Hi,
I am trying to interface WM8960 CODEC with nRF52832 using (I2S and I2C) .
Problem I am having is with TWI scanner and also sending data to the know i2c address . have...
SES 5.44
nRF52840-DK
GNU Arm Embedded Toolchain: 9 2020-q2-update from here
S140: 7.2.0
Project is C code only
Project Setup:
Linker Script File (copy from...
Hello,
I am a research assistant at the Norwegian University of Science and Technology. We have in the past been using the micro:bit v1 for our practical labs which purpose...
Hi, When I hook the nRF5340-DK board to my PC, the SEGGER J-Link OB debug chip bothers me popping up a GUI that exposes the board as a USB mass storage device. How to get...
I'm using Android DFU library 1.11.1 and occasionally I see "E/DfuBaseService: Connection state change error: 133 newState: 0" errors. It appears they happen when the initial...
When using nRF Connect SDK v1.6.1, a BLE peripheral that supports 2 simultaneous connections could be created by including these lines in prj.conf. These lines set the Link...
Hi,
this is kind of continuation of my previous ticket . After solving it the last time I thought that I don't need wait_for_flash_ready() function as it caused some problems...
I just buy nRF5340.
I install nRF Connect in my PC.
and install bluetooth app.
I just select my pdk.
log show
INFO Connected to device with serial number: 000960119975...
