I'm trying to implement channel scanning in our nrf24lu1p based USB dongle.
I'm following the specs and basically loop though each channel ;
loop
stop listening
set...
Hi,
I am using the NRF8001 in UART mode and attempting to bond with my android device (Lollipop 5.0 Nexus 6).
i am using the nordic arduino sdk which is found here:...
Hi, I'm using the nRF8001 in an application that requires security so bonds to the remote client/central. My device supports firmware upgrades that may involve new nRF8001...
Hello.
Initially when reading the Gazell documentation I didn't think it'd be a problem but now in Keil seeing this has introduced some doubt whether it's a thing:
...
We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hello DevZone,
A product I use uses NFC tag type 2 to communicate. It usually communicates to a separate chip but I want to replace this with the nRF52832.
I opened...
Hello,
I'm working on a product where we want the nRF52840 to be able to reset itself in hardware . This is currently done via an IO that drives a SHUTDOWN# signal into...
Hi,
I'm using TWI to control accemeter(MMA452).When I used TWI SENSOR to read my sensor, it didn't work normally.
The address of MMA8452 is 0x1C,so i want to read...
The separation of flash memory into a region for the application core and one for the network core on the nRF5340 seems rather cumbersome and error-prone.
I'm especially...
Hi,
will qmi_wwan or gobinet driver be available for nRF9160? PPPD is not available. It is quite a limitation in use to miss ethenet interface based connectivity.
Regards...
Hi everyone, I’m have a wired network of 1000 devices (relay switches) that I’ve been tasked to upgrade to wireless.
Devices are inside a warehouse, about a pallet apart...
Hello All,
I am developing product using nRF52840 Dev-kit and SDK 4.1 for zigbee and thread.
I have created the new solution using tool chain - C:\Program Files (x86)...
Hello,
I'm using the NRF52840 with the NRF5 SDK v15.3.0 and S140.
I was trying to include the nrf_fstorage library into an existing project. The problem I experienced...
Hello,
I modified a sample app "blinky" on segger, to include main.cpp instead of main.c Then when I built, I got a compile time error stating in main.cpp "void main(void...
Hello.
I'm looking at options for a BLE device that has fairly small application requirements. It would essentially be a button, so the peripheral blinky example would make...
Hi Nordic!
We are gonna do pre-compliance testing of our custom board, with mounted nRF52840 and nRF9160 SICA B0.
We are looking for any software available from Nordic...
Hi,
with reference to case ID:278209, I was suggested with a resolution to add in CMakeLists.txt I need information on all such (CMakeLists.txt) available tags/labels...
hello,
I tried to read adc sampling value from (NRF_SAADC_INPUT_AIN0~ NRF_SAADC_INPUT_AIN4) with pip mode.
Here are my code as followings
If I have no any voltage...
Hi, there.
I'm trying to implement DFU over UART for a NRF5340. I have read the documentation and have understood this will require the use of a bootloader and I wish for...
Hi,
I want to update nrf52840 application DFU over serial UART link from other MCU. We have go through secure bootloader example in SDK ("SDK\examples\dfu\secure_bootloader...
