I'm trying to implement channel scanning in our nrf24lu1p based USB dongle.
I'm following the specs and basically loop though each channel ;
loop
stop listening
set...
Hi,
I am using the NRF8001 in UART mode and attempting to bond with my android device (Lollipop 5.0 Nexus 6).
i am using the nordic arduino sdk which is found here:...
Hi, I'm using the nRF8001 in an application that requires security so bonds to the remote client/central. My device supports firmware upgrades that may involve new nRF8001...
Hello.
Initially when reading the Gazell documentation I didn't think it'd be a problem but now in Keil seeing this has introduced some doubt whether it's a thing:
...
We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hello. I'm sorry for my bad English. I'm currently working on a development using nRF52840 based on ble_app_blinky, which is an example of s140 and peripheral. So, I want...
2. In the nRF sniffer software, the device I'm interested in does not show up in the "Source" column with its addess, b8:80:4f:6b:b6:9e, but as "TexasIns_6b:b6:9e". It seems...
Hello,
I'm finding problem to generate the library uECC.a to use in project secure_bootloader for nRF52833 (SDK17) using SEGGER.
I started from project SDK_17\examples...
i want that my device shall advertise after i press a button for 5 seconds. there is a feature of long press for button kindly assist as how to use this for advertising
Hello,
I am currently trying to combine the NRF52840 (Development kit) with the Arduino Ethernet shield containing an W5500.
I was wondering if there is any example...
I have been trying to figure out how to use SPI on nRF Connect SDK. I cannot find a simple enough example to get started other than the convoluted SPI flash example or the...
We find a Beaocn from other distributor , it got very less fluctuations. RSSI table show below.
Test method: 10 RSSI were collected from a hand-held mobile phone at...
Typically the Base address registers and Prefix registers are used to configure up to 8 logical addresses and then RXADDRESSES is used to filter which of the 8 logical address...
Hi,
The new AT monitor have a hard-to-reproduce bug: the subscriber entry list alignment is not specified in the linker script. Since structs are always aligned, that means...
Hi,
im porting our nrf9160 application from SDK 1.3 to SDK V1.6.1. and facing error while accessing NVS device in SDK V1.6.1.
in SDK 1.3 i used "device_get_binding(DT_FLASH_DEV_NAME...
Hi,
I have have certain thread that I would like to be active during a ble connection. I can suspend it when not needed and resume when connected. But as long as the thread...
Hi:
I'm using SDK V17 & encounter a problem.
in my project, the nRF52832 doesn't broadcast at all.
Once the button1(EVK btn1) is pressed and lasting 5 seconds,
nRF52832...
I'm very new to the NRF boards. I can not find any information on the USB port (programming port). I would like to use that to read serial data written from a terminal program...
I am using the nRF 52840 development kit to explore Thread. I am using the 'open nRF Connect SDK' command to get the project. I would like to use the 'overlay-usb.conf' option...
Hi,
I am also facing same issue i am able to read the version register correctly and able to perform self test successfully
I am using 17.1.0 n RF5 SDK
I am developing...
