Hello all,
in my previous question (Switch between applications (multiple services.h)) I got the advice to merge my two services into one service, including a HID over...
I am trying to create an nRF8001 based application that will broadcast battery levels (pipes broadcast, set), and give out temperature data (pipe indicate - TX_ACK) to connected...
Hi,
I'm using redbearlab's nrf51822 board. It is a arduino compatible board and hence it is using 0,1 (mapped to 9 and 11 for nrf51822). How do I make printf print to this...
An external PA/LNA is used to extend range of nRF51822, and S110 is used for BLE, How to switch between PA and LNA? and how to disable PA/LNA when there isn't transceiving...
Hi...
Can anybody help me to run ble_peripheral example (ble_app_hrs for S130). I have build and load the code successfully but cant see the advertisement. But while debugging...
I am working with the nRF8001, and I'd like to create a services.h file that will let me broadcast battery level and as well as allow temperature to be read by a peer.
...
Hi We have an application where we what to read i2c sensor data over the air to an iPhone. We've taken ble_app_uart_S130 project and grafted in some twi_hardware code. There...
Would like to capture the HCI flow through rpmsg (Rx and TX) using the btmon tool between application and network core. could not successfully do it.
Procedure:
1. Build...
As mentioned in the DK board User guide nRF52840_DK board is preprogrammed, so, till now we didn't flash the DK board.
I tested the nRF52840_DK board using J2 USB connector...
Hello, with the new version of the nrf5340 version D in the NET CPU RTC0 stops to work and the RTC0 IRQ is not called
now for example the counter is stopped at 87 and the...
Hi,
My problem is that I can't sniff any advertising packet using Wireshark.
I have well followed the detailed procedure https://infocenter.nordicsemi.com/index.jsp...
BLE app uart code write to the BMD 350 device. BLE is disconnected.
If any reasons?
How to configure the TX and RX pins ? when i change the pins, fatal error will come...
Is clearing the NRF_UART_EVENT_RXDRDY really sufficient before exiting the IRQ handler? Since Cortex M4 is used, there's no need to clear the pending register (to avoid the...
Hi, Could you pls check, is it ok if these logs happened?
No firmware defined for selected device Please make sure the device has been programmed with a supported firmware...
Hello
I would like to modify the example "ble_thread_dyn_mtd_coap_cli_nfc" to use Just Works pairing instead of OOB with NFC.
To do this, I modified this in sdk_config...
Hi,
I worked few years ago on a project with the configuration below :
nRF Mesh SDK V1.0.1
nRF52832
I used the light switch example where the client and the provisioner...
Hi, I have built a project upon the aws_iot-example. There are three shadow-topics that the device may publish to (/update, /get and /delete). To me it seems there is no possibility...
So I'm trying to get to grips with the ble_app_blinky example from nRF5_SDK_17.0.2_d674dde\examples\ble_peripheral\ble_app_blinky
To start with I grabbed the hex file ble_app_blinky_pca10059_s140...
Hi, 1. In ncs v1.5.0 nRF5340 I need to drive a spi peripheral w25q128 2. How do I generate this file?
3. Where can I find the syntax rules that generated this file? 4. Can...
Would like to capture the HCI flow through rpmsg (Rx and TX) using the btmon tool between application and network core. could not successfully do it.
Procedure:
1. Build...
