Hello, I have established the connection between two pca10001 boards, one as central and one as peripheral using multilink_central and multilink_peripheral. I have serial...
Hi,my friend,
Now,I use nrf905.Situation is as follows:
I use the NRF PCB circuit of data manual.Nrf905 work, often loss of data.
1.The Product host is to use the stick...
Hi,
I want to use the Blend Micro with more security. I want use a passkey for the Bluetooth connection. For example through the iOS Device.
Is it possible? Static passkey...
How do I receive multiple signals simultaneously at a single receiver (433MHz) with multiple transmitters ?
I am working on a polling system. This one is similar to the audience...
Hello,
I established a connection between my central and peripheral module. Now i want to write characteristic value on peripheral. I tried with sd_ble_gattc_write function...
I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
Hi, my friend,
I've been with nrf905. I use a 16-bit CRC check.
But I encountered problems in use:
1.Nrf905 16-bit CRC check format is CRC-16(IBM):X16+X15+X2+1 or other...
Backround: We are planning to use TF-M with a two-stage bootloader (NSIB & MCUBoot) using dual-slots for secure and non-secure images. We need to support configurable fixed...
Hello Devzone,
In our product we are working with a nRF52840 microcontroller and periodically transmitting large sums of data to a PC or a phone.
We noticed that over...
Hi All,
I have designed my custom pcb board for nrf52811. With the Jlink the IC is detected in visual studio code also it gets programmed. But i did not see its working...
Hello,
I am currently working on a project that involves interfacing the TLV493D 3D magnetic sensor with the nRF52832 microcontroller. I would appreciate any guidance or...
Hi
We use the nRF52832 for an NFC device. The device is 99.9 % in the system off state to save power as much as possible. because the device is power by a button cell battery...
Hi
I'am using nRF util version 6.1.7 for a long time to generate a DFU packages. I need to debug my ble data so i thought of using ble sniffer from nrf util. But the ble...
Hello! We have a project under nRF Connect SDK and Zephyr. It uses Bluetooth central and peripheral role (GATT client and server).
The project works good under SDK v2.7...
Hi,
I'm trying to connect to the nRF52840 dongle using nRF Connect for Desktop Programmer v4.5 on MacOS 15.2 so I can update the firmware. The dongle has the red flashing...
I've then tried both the command " nrfutil ble-sniffer sniff --port /dev/ttyACM0 --coded" as well as "nrfutil ble-sniffer sniff --port /dev/ttyACM0 --coded --scan-follow-aux...
Helo,
I lost the PUK to my iBasis SIM, so I can't register it on nrfCloud.com for my 9160. Is there a way to recover it or do I need to buy a new one? (If so, where?)...
I tried to write the following simple '.overlay' file:
However, I am getting the following error:
but if you look inside the .dts files provided by the 'nrf52dk' I...
Hi everyone,
I’m working on a Zigbee application using the nRF52840, and I’ve been experiencing periodic reboots that I cannot figure out how to resolve. I’ve already updated...
Hello. I have a question about the development environment when developing using nrf.
When you build a new board and make firmware without using dk or ek, do you usually...
Hello everybody! There is a problem and help is needed. With the help of hardware timers, I need to generate a signal with a given accuracy. The frequency is 998 Hz. I'm using...
We are working on developing wearable device (like band) with cellular-IoT network connectivity. Considering available features and size, nRF91 series seems to be a good choice...
