I am trying to create an nRF8001 based application that will broadcast battery levels (pipes broadcast, set), and give out temperature data (pipe indicate - TX_ACK) to connected...
Hi,
I'm using redbearlab's nrf51822 board. It is a arduino compatible board and hence it is using 0,1 (mapped to 9 and 11 for nrf51822). How do I make printf print to this...
An external PA/LNA is used to extend range of nRF51822, and S110 is used for BLE, How to switch between PA and LNA? and how to disable PA/LNA when there isn't transceiving...
Hi...
Can anybody help me to run ble_peripheral example (ble_app_hrs for S130). I have build and load the code successfully but cant see the advertisement. But while debugging...
I am working with the nRF8001, and I'd like to create a services.h file that will let me broadcast battery level and as well as allow temperature to be read by a peer.
...
Hi We have an application where we what to read i2c sensor data over the air to an iPhone. We've taken ble_app_uart_S130 project and grafted in some twi_hardware code. There...
I am interested in the S130 ability to hold 3 central -> peripheral links over BLE, and am looking for some evidence that this has been accomplished with extremely low-power...
I am using the nrf5340 on a nrf7002fk dev kit. I am interested in low power operation so I am measuring the power consumed.
I am running a simple app:
int main(void) ...
Hi everyone,
Could someone help me with the following use case?
Task description: I'm working on a firmware update procedure based on the smp_svr project. I'm trying to...
Updating from NCS2.6 to 2.8, the access to my QPSI Flash chip got broken (mx25r64, connected and configured using QPSI exactly as per the nrf5340DK board)
DTS entry:
...
Hello,
I have made a project that was based on the nRF9151 Development Kit and it works great. I had to select the -ns configuration to get anything to ever build and now...
Hello, as the title suggests, I have an issue when powering the nRF9151 DK with an external power supply. Normally, I power through USB, and it's fine. However, when I followed...
hello nordic, we are looking at nrf52820 to satisfy some requirements. 1: We plan to power off single cell Lithium application which can be 2.7V - 5V trhu VBUS / VDDH and...
Hello,
On our custom PCB, we’re using an nRF5340 and an nRF7002 via the WM02C module.
In our devicetree, we are using the following QSPI node configuration.
We’ve produced...
Hello,
We have implemented and tested the scanner code for the nRF52832. Now, we want to migrate the same code to the nRF52833. The project has already been configured for...
I'm getting a " Must include ICCID or EID to associate a SIM" message when trying to register a SIM.
And yet the ICCID and PUK have been entered into the form.
What does...
Hey everyone,
Does anyone here have experience with firmware OTA updates over the JIO NB-IoT network? The process seems a bit different since JIO Cloud always sits between...
I downloaded NCS 2.9.0 from nRF Connect For Desktop and sdk-sidewalk following Nordic's instructions. After successfully downloading everything, I built the sample "Hello...
Hi Team,
I have added the NUS function in the Matter project. After the commissioning broadcast is turned off, NUS broadcast will automatically start. I want to manually...
Hi,
Now, I'm doing a project. A device node sends picture data and the other one receives these data. Then the receiver shows the picture on the SSD1306 display.
At receiver...
Hi
When i used for DK nRF54L15, PMIC nPM1300 was burnout.
and this PMIC i want to directly replace the DK with a new npm1300.
Can the software that comes with this...
Hi,
I am facing issues while setting up the PPK2 in one of my desktop.
The same hardware is working fine on another desktop.
Can you let me know what could be missing...
