Hello all,
in my previous question (Switch between applications (multiple services.h)) I got the advice to merge my two services into one service, including a HID over...
I am trying to create an nRF8001 based application that will broadcast battery levels (pipes broadcast, set), and give out temperature data (pipe indicate - TX_ACK) to connected...
Hi,
I'm using redbearlab's nrf51822 board. It is a arduino compatible board and hence it is using 0,1 (mapped to 9 and 11 for nrf51822). How do I make printf print to this...
An external PA/LNA is used to extend range of nRF51822, and S110 is used for BLE, How to switch between PA and LNA? and how to disable PA/LNA when there isn't transceiving...
Hi...
Can anybody help me to run ble_peripheral example (ble_app_hrs for S130). I have build and load the code successfully but cant see the advertisement. But while debugging...
I am working with the nRF8001, and I'd like to create a services.h file that will let me broadcast battery level and as well as allow temperature to be read by a peer.
...
Hi We have an application where we what to read i2c sensor data over the air to an iPhone. We've taken ble_app_uart_S130 project and grafted in some twi_hardware code. There...
Hi
After nRF Connect for desktop was upgraded to v3.6.1, programmer application cannot recognize all DK boards, including PCA10040/PCA10056/PCA10090.
It showed the error...
Can I use nRF21 in GPIO mode (not SPI) using the PA/LNA assist feature of the S112 soft device?
Per section 5.3 of the datasheet, it seems I could wire the PDN pin to be...
Hi,
I am learning how to write and read from flash memory on nRF52833 dev board for a BLE application.
I followed the heart rate example as shown in https://devzone.nordicsemi...
I am writing an application for the nRF52DK which uses two additional push buttons besides the 4 already present on the board.
Using GPIOTE the detection of the button press...
I have a working project that uses the NRF_LOG module to send debug outputs over the UART backend. When just using the logging module everything works correctly.
I added...
Hi,
Is it possible to set multiple APNs in nrf9160 and with fallbacks to next APN if one not working?
Suppose if we set 2 APNs at CID=0 and CID =1 positions using AT+CGDCONT...
Hello I am trying to execute the functions of SPIS and thread on nrf52840 Refer to his code to write nrf52840 SPIS: https://devzone.nordicsemi.com/f/nordic-q-a/68854/nrf5340...
Hi,
I am trying to configure the nRF Connect SDK on a Mac running Catalina for the first time and have followed the nRf Connect v3.6.0 - Getting Started Assistant.
I am...
I am new to the Segger Studio and nRF52840 . (However not a Newbie to Microprocessors)
Off the Bat :- Blinky example works fine...
.....however when I try to get the PWM_driver...
Hello, I wanted to know do this chip ( nRF52810) has both tag (beacon) and receiver function? If cannot is there any other Bluetooth chip suggestion? My main idea is to use...
I am new to Arm and Nordic devices and I am trying to port the Thingy52 firmware to SES so we can add some additional sensors.
I have got the Thingy52 firmware to compile...
Hi Nordic Community,
I follow the below link to create an openthread border router. I successfully send sensor data on things.io.
https://infocenter.nordicsemi.com/index...
I've implemented the nRF52840 QIAA var5 reference design in hardware and it works well. For L2 (10uH) and L3 (15nH), in series off the DCC pin B3, could you perhaps recommend...
