I am trying to create an nRF8001 based application that will broadcast battery levels (pipes broadcast, set), and give out temperature data (pipe indicate - TX_ACK) to connected...
Hi,
I'm using redbearlab's nrf51822 board. It is a arduino compatible board and hence it is using 0,1 (mapped to 9 and 11 for nrf51822). How do I make printf print to this...
An external PA/LNA is used to extend range of nRF51822, and S110 is used for BLE, How to switch between PA and LNA? and how to disable PA/LNA when there isn't transceiving...
Hi...
Can anybody help me to run ble_peripheral example (ble_app_hrs for S130). I have build and load the code successfully but cant see the advertisement. But while debugging...
I am working with the nRF8001, and I'd like to create a services.h file that will let me broadcast battery level and as well as allow temperature to be read by a peer.
...
Hi We have an application where we what to read i2c sensor data over the air to an iPhone. We've taken ble_app_uart_S130 project and grafted in some twi_hardware code. There...
I am interested in the S130 ability to hold 3 central -> peripheral links over BLE, and am looking for some evidence that this has been accomplished with extremely low-power...
Hi !
I am working with a NRF52832 and with SDK 15.2.
For my application, I need sometimes to deactivate the Softdevice to begin some radio tests.
So I have programmed...
I am doing the procedure described in the nRF52840 specification, figure 193 "UARTE reception with forced stop via STOPRX".
I am using 1Mbps with hardware flow control....
I'm testing out the Thingy91 Asset Tracking Application, but I notice when I poll the Accelerometer, I only get junk data back. +/-20m/s^2 on all axis. I'd test this application...
Hi! This is the first time that I develop a BLE system with this MCU, I want to know if it is necessary to install so many vias making a shield around the entire pcb. If so...
Hi,
i'm using SDK11 with NRF52832
After a pin falls from HIGH to LOW The GPIOTE_IRQHandler calls a function in my program to read 8 bits from the bus (Inside the interrupt...
Following the seminar today I tried to build and run this example.
built on command line using west (non-secure nrf9160-DK target)
in a continuous loop I get
```
SPM...
I want to dump lengthy log data out through an RTT connection if the JLink is connected but NOT spend that time if there's no physical RTT channel present. The idea is that...
1.Customers need to use nrf52833 for design and production in this package: WLCSP package, 3.175 x 3.175 mm
2.I noticed the description in this manual:nAN-38 WLCSP Handling...
At present, the SMS is sent normally. The format of nrf9160 is 7bit, and can send a maximum of 160 characters. However, how to send it in packages if the content exceeds 160...
We are looking for a Bluetooth 5.1 indoor positioning solution at precision around 1m.
Could you help figure out which platform/reference design is capable of implementing...
Hi,
I have configured the MQTT simple sample from nordic to send data to our broker, this works just fine at the moment.
I would like to send Json formated data to the...
Hi all,
I was playing around with radio and trying to create interupts for the event_end flag and i've now messed up completely and even without the code i added the chip...
I am working with the PWM driver to drive a stepper motor and I have a couple of doubts about when all the events are generated. My doubts are related to events:
NRF_PWM_EVENT_SEQEND0...
Hi,
I try to implement a disconnection after wrote a characteristic parameter. This byte change the working mode of my systeme.
So user connect, write the field to change...
