Hi,
I'm using redbearlab's nrf51822 board. It is a arduino compatible board and hence it is using 0,1 (mapped to 9 and 11 for nrf51822). How do I make printf print to this...
An external PA/LNA is used to extend range of nRF51822, and S110 is used for BLE, How to switch between PA and LNA? and how to disable PA/LNA when there isn't transceiving...
Hi...
Can anybody help me to run ble_peripheral example (ble_app_hrs for S130). I have build and load the code successfully but cant see the advertisement. But while debugging...
I am working with the nRF8001, and I'd like to create a services.h file that will let me broadcast battery level and as well as allow temperature to be read by a peer.
...
Hi We have an application where we what to read i2c sensor data over the air to an iPhone. We've taken ble_app_uart_S130 project and grafted in some twi_hardware code. There...
I am interested in the S130 ability to hold 3 central -> peripheral links over BLE, and am looking for some evidence that this has been accomplished with extremely low-power...
I'm trying to implement channel scanning in our nrf24lu1p based USB dongle.
I'm following the specs and basically loop though each channel ;
loop
stop listening
set...
Hi,
Someone has been working with Alarm Cluster. I tried to implement it on multiprotocol dorr lock example but it was impossible. I have been reading ZCL library revision...
Hello,
I am trying to PCA10040 example project program to NRF52810 BLE module.
I just know that the 52810 has different(small) memory with respect to the 52832.
So,...
I have compiled ble_app_blinky sample code from nRF5_SDK_17.0.2_d674dde SDK and loaded it with s132_nrf52_7.2.0_softdevice.hex in my nrf52382 board. I can discover this device...
Hello,
I want to use a Li-Po battery with my nRF52833 development kit and I can't find the specific name of the J6 connector in the DK documentation. Does anyone know...
Hello ! I am working on the asset tracker project on NCS 1.4.0. Since I switched to this NCS, I have an error that comes up very often (once in two or once in three): get...
Online rajAsthana a few seconds ago in reply to Einar Thorsrud
Hi Einar,
Now I am able to put my board(nrf52840) in DFU mode with buttonless code using Esp32 as...
Hi,
I using nrf52832 evk board and sdk17(S132). I want to add the internal temperature sensor reading to the ble_app_buttonless_dfu_pca100400_s132 code present in the examples...
Hi,
1st time using nRF52840 - EV-BT840 on Keil V5.25.20
I use SDK 1702, reference to example examples\dfu\secure_bootloader\pca10056_s140_ble
My question is what softdevice...
Hey,
I have isnstalled ncs v1.3.1 and the toolchain specified in the instructions ofr 1.3.1.
I am trying to utlise the date-time library in the https_client example. ...
Hi Great Nordic Support Team:
Our clients are developing products with 『 nrf52840-WLCSP』. And they find out that there are some mis-information on the spec.
It's described...
Hi,
Dear nordic friend,I am trying to download NCS1.31 by using toolchain manager,but it work bad,show in below.
I have use some ways，to make me can visit the web in Europe...
Hi, I'm having difficulties driving SDOUT when it's configured to pin 19 on the NRF52840. I can operate the peripheral and see output data when my WS2812_PIN macro is assigned...
Hi all,
I am interfacing with a CAN Controller (MCP25625) that sets an Interrupt pin when data is ready (active low). That pin is then connected to a GPIO on the nRF9160...
Hello
I'm using a passive buzzer controlled by PWM. When PWM is set and run, the buzzer will continue to output small noises.
This is probably a code problem. Below is...
