Hi,
We're looking for a low-latency 2.4GHz solution (not BLE) and the nRF51822 is oft-quoted as providing low latency, but what are the typical ms figures we could achieve...
Hello all,
in my previous question (Switch between applications (multiple services.h)) I got the advice to merge my two services into one service, including a HID over...
I am trying to create an nRF8001 based application that will broadcast battery levels (pipes broadcast, set), and give out temperature data (pipe indicate - TX_ACK) to connected...
Hi,
I'm using redbearlab's nrf51822 board. It is a arduino compatible board and hence it is using 0,1 (mapped to 9 and 11 for nrf51822). How do I make printf print to this...
An external PA/LNA is used to extend range of nRF51822, and S110 is used for BLE, How to switch between PA and LNA? and how to disable PA/LNA when there isn't transceiving...
Hi...
Can anybody help me to run ble_peripheral example (ble_app_hrs for S130). I have build and load the code successfully but cant see the advertisement. But while debugging...
Hi,
I am want to do wake up on motion when any threshold value generated by icm 20948 accelerometer I want to send an interrupt from icm 20948 to nrf52832 to wake up from...
Hi !
I'm using the nrf52832 with SDK 11 as pheripheral.
In Android phone the bonding and the scan request working great with my unit !
However, in IOS
1) i do scan...
Hello,
I am working with LPN example of SDK 3.1.0. In the example I need to change the poll interval time based on our application requirement.
I looked at this equation...
Hi Nordic team,
I have a curious problem I need a little help with:
(NRF52840 & SDK 15.3)
I have a project which is an integration of the ble_uart example and the serial_uartes...
I have searched your forum and have found several references to my issue; however, I have not been able to get anything resolved.
I am using the nRF51822 which is part of...
Hello,
I am using nRF52832, SDK_15.3.0, S132 SoftDevice and Segger for flash the image. I am using ‘ble_app_blinky’.
I have gone through “Application Timer” tutorial...
I have a development board and load the client central BLE blinky to it, then the peripheral BLE blinky to my custom board and power up and the central development board stays...
I was wondering if it is possible to do HTTP requests with the nRF9160 just by using AT commands? Since this is usually possible with such kind of modules.
The reason is...
Hello everyone,
I've got a three type of devices: 1 Central device, 2 Peripherial devices, and mulitple beacons. Central is connected with two peripherial devices with...
Hi Devzone,
We are using the nRF52 DK in a prototype which is under stress, and we noticed that any bending of the board breaks the BLE connection.
To easily replicate...
Hello,
I am currently writing a script whose purpose is to automatically provision and configure devices.
My question is related to the devkey_handle and address_handle...
With SDK 14.2.0 and S332 softdevice, I'm using UART to control ESP8266 WiFi module with AT commands and I'd like to replace app_uart (+FIFO) with nrf_serial , in order to...
Hi,
I am setting OOB with sd_ble_gap_auth_key_reply() method { 0x11, 0x11, etc 16 bytes }, but when trying to connect with desktop nRF Connect there is an error 132 inside...
Hi,
I am getting errors when attempting to include the nvs library to save data to flash storage on the nRF9160 DK. My CMakeLists.txt:
I get the same errors with or...
Hi,
We tried to use a smartSIM from Sierra Wireless with the nrf9160DK without success.
The nrf91 can connect to the LTE network after a few minutes (LED4 steady). However...
