Hello,
I see when you import an example from the pack installer ( for example pwm, ble, timer examples ) it arrives with the misc controls --c99 on by default , so I cannot...
Hi,
We're looking for a low-latency 2.4GHz solution (not BLE) and the nRF51822 is oft-quoted as providing low latency, but what are the typical ms figures we could achieve...
Hello all,
in my previous question (Switch between applications (multiple services.h)) I got the advice to merge my two services into one service, including a HID over...
I am trying to create an nRF8001 based application that will broadcast battery levels (pipes broadcast, set), and give out temperature data (pipe indicate - TX_ACK) to connected...
Hi,
I'm using redbearlab's nrf51822 board. It is a arduino compatible board and hence it is using 0,1 (mapped to 9 and 11 for nrf51822). How do I make printf print to this...
An external PA/LNA is used to extend range of nRF51822, and S110 is used for BLE, How to switch between PA and LNA? and how to disable PA/LNA when there isn't transceiving...
Hello. A re-connection failure problem happens on our products.
chip:nRF52832 SoftDevice:S132 SDK v11.0
1. pairing and bonding on LESC 2. reset connection and re-connect...
Hi,
I have connected and SPI flash module to my pca10040 dev board. I wrote a test cycle of erase/write/verify for the entire flash and it works correctly. My initial pinout...
Hi,
I need some very simple file system to use on an external SPI flash. I gave a quick look at Flash Data Storage and it should be ok for me. I am not sure though why it...
Hi,
Disclaimer - this is definitely a question where one picture worth a 1000 words... ;)
My app use timeslot api to get a free time period to do some hard real-time...
Hello. How can I send binary data (in order to not convert it to ASCII string) over UART?
I have sensor data (obtained over BLE). Every measurement is 13 bytes, sample frequency...
Good day!
Thank you for your consideration of my problem! The system is an nRF52832 utilized as a motor driver of a small 2W high rpm maxon motor. The system performs as...
Hello,
I am trying to evaluate the nRF52 dev kit. The "getting started" HTML documentation has a link for "Setting up the development kit". This links loads "Oops (400)...
Despite all the questions on this forum for how to change PWM frequency on the fly, I found no mention of anyone using "WaveForm" mode. Perhaps it's new? There are also no...
Dear all
I have a service with an UUID. Let's say 11111111-2222-3333-4444-555555555555
I also have two characteristics that belong to this service:
66666666-7777...
I am using an nRF52 DK to build a prototype for a product. The device needs to have a connectable advertisement (as peripheral with multiples connections possible) and at...
Hello, thanks for reviewing this. I am trying to install and run Zephyr on the nRF52840 module that is on-board the nRF91 DK board. I have gone through the setup process and...
I'm doing this:
1. Start a scan, with these parameters:
#define SCAN_INTERVAL 0x00A0 /**< Determines scan interval in units of 0.625 millisecond. */ #define SCAN_WINDOW...
Hi
We are evaluating the nRF52832 for use in a medical application, I have modified the example ble_app_cgms_pca10040 to drive our evaluation hw. We are using the Nordic...
I am trying to interface nRF52-DK (PCA10040) with an external MCU (PIC24FJ128GC010) using UART. When trying out the ble_app_uart example in the SDK version nRF5_SDK_15.2.0_9412b96...
