I'm trying to implement channel scanning in our nrf24lu1p based USB dongle.
I'm following the specs and basically loop though each channel ;
loop
stop listening
set...
Hi,
I am using the NRF8001 in UART mode and attempting to bond with my android device (Lollipop 5.0 Nexus 6).
i am using the nordic arduino sdk which is found here:...
Hi, I'm using the nRF8001 in an application that requires security so bonds to the remote client/central. My device supports firmware upgrades that may involve new nRF8001...
Hello.
Initially when reading the Gazell documentation I didn't think it'd be a problem but now in Keil seeing this has introduced some doubt whether it's a thing:
...
We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi!
I am trying to use the NFC " writable_ndef_msg " code along with the " ble_app_uart " code from SDK 15.0 with Softdevice s140 on nRF52840 DK. I am using keil-MDK 5...
How can I be 100% sure the nRF52832 chip is running properly?, what I do to power up the chip is feed it with a regulated voltage of 3.3V (which really is around 3.17V), on...
We use Nrf_studio to connect our board by uart to enter direct test mode.
But an error occurs in serial connection.
I want to know， use our own project program is allowed...
I have already pressed reset in the dongle, it was pulsing red. And when I write it allways says the same error. I have done this experiment in Ubuntu 16.04 and Windows 10...
Dear all,
I'm struggling writing 32 bytes with FDS in SDK 14.
This is what I do:
Init
(void) fds_register(fds_evt_handler);
fds_init();
while(!is_init) {
sd_app_evt_wait...
Hi, I am using nrf51822 Development kit with 3 buttons, each buttons has different functions. (i) 1st Button is used for the wake the module from sleep mode. (ii) 2nd Button...
Hi I using nrf51DK using keil MDK 5 softdevice s110.
I need to update battery level on every 60s and I have initialize timer and start with this code.
static void battery_level_meas_timeout_handler...
I'm trying to implement extended advertising, using BLE_GAP_PHY_2MBPS to offload 255byte advertisement payload to channel data, defining BLE_GAP_PHY_1MBPS as primary phy ;...
Hi
I am trying to broadcast manufacturer data (beacon example) while changing data from second to second. For that I am trying to use timer2 (as timer 0 is used by SD, right...
Greetings,
For Bluetooth Declarations, will new QDIDs be generated to account for the additional required tests as of January 24, 2019 in TCRL-2018-1.
I'm mainly interested...
Hi,
I need to interface LIS2DH through SPI. I tried many SPI Master example but I am getting all the values as 0XFF. Even the WHO_AM_I registers value is getting 0xFF
...
Hi, I have an EMG muscle sensor which needs to be sampled at least 500Hz. Can I sample at the required frequency and transmit at the same time over BLE NRF51822. If not please...
Hi, I am new to the bluetooth mesh concept but I have tried creating one using nRF52 DKs.I have worked the light switch example but I am stuck there without being able to...
Hi everyone,
I bought the nRF51822-04AT module but I'm a newbie and all the documents talk about nRF development kits which they make me confused about programming. Now...
Hi,
I am working on the NRF51822 module with BLE-400 Board to develop the application.
And I need to detect the USB-Connection when it will be in the sleep mode, After...
