We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Currently, I am creating a CIS-connected device using nRF5340 Audio on a homemade board.
Since the circuit configurations of the Gateway and Headset are different, I have...
I just got a fresh Win install and installed a new version of vs code (details below) and lo and behold the nrf welcome page is empty! Apparently, this was changed a while...
Hi I am looking for some advice with regards to getting a Fanstel BU840XE ( BU840XE, The longest range, Remote USB Dongle for BLE 5, Thread, Zigbee — Fanstel ) device to function...
Hi team,
I am getting secure fault after PPP started in SLM (v2.6.1) application.
here is the snapshot of the error message
Anyone having same issue and resolved please...
I am experiencing an issue with the I2C device on the nRF5340(our custom board) where it is unable to read/write to the sensor, resulting in a return value of -5.(EIO)
Details...
Hi
I'm chnaging the Secure Bootloader to an external falsh for bank1, connected with QSPI.
In the function on_data_obj_write_request is the call for nrf_dfu_flash_store...
Hi,
I have a project with an nrf9160 running zephyr. Can codechecker be set up in the build in nrf connect in vs code so that when a build in vs code is done it runs code...
Hello,
I am migrating an application based on the old Nordic SDK16 to the NCS Zephyr SDK.
My workspace is using Zephyr commit f8f11338, nrfconnect/mbedtls commit de1b3f57...
Hello, I am trying to debug why my device is failing to work 100% of the time. What happens is an app makes a connection to the device, sends a command to the device, receives...
Hi all,
I' have a custom board with an nRF9161 chip. I have a custom connector to program it with SWDIO/SWCLK. For the moment I'm trying to detect my board with nrf programmer...
Hello!
I have a custom service that I try to implement on two nrf52840 DK, where one is supposed to act as a GATTClient and one is going to be a GATTServer.
The service...
hey there
i design my own board based on nRF5340, now i want to write a code for wireless boot loader on it with ble. on my board i have a nor flash for this goal. in part...
Hi,
I am not sure how to read from a characteristic which doesnt have notify property in them. I started looking into nrf_ble_gq_item_add() But I am not sure on what parameters...
