Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Hello everyone,
I got a task which I try to implement using a NRF51822 iBeacon board.
The Task:
Advertise a Device and provide a mechanism to connect without traditional...
Hello, I'm working with the EK PCA10003, that has the NRF51422. I'm trying to read the information of the accelerometer MPU6000 with an ISP interface. At the moment I cannot...
I'd like to use the GATT/GAP driver from an ARM based Linux system. Is there any possibility of getting a library compiled for ARM or (cough) the source code to build it myself...
When I load the firmware, the firmware starts running fine.
but once I power off then on tue device the firmware crashes at a certain point while in the main loop with no...
Hi All,
As part of the software development, we are required to use an automatic tool for Code Coverage.
We use an nRF52840 device, C language and 15.3.0 nRF SDK on...
Has anyone succeeded in BLE bonding with a Philips Hue lamp or a Hue smart plug with a nRF52? Directly with BLE, without a gateway. I suppose I have all the rest figured out...
Mcuboot manages firmware versions and is able to avoid fw downgrade.
Is it possible to define a product id to avoid to exchange fw for different product of same manufacturer...
Hi,
I want to prepare the scrip for Wi-Fi radio test commands. I am testing the RF performance on nRF7002dk and in order to test the each channel i have to run the below...
Hi,
We have run into an issue when debugging code with the nRFconnect sdk debugger. A breakpoint set in an interrupt service routine is not hit, however, we can see through...
Hi,
I have a piezo microphone with analog output and would like to record from it using the Line In AUX on nRF5340 Audio DK.
Currently, I am using the break out pins...
Current goal is to be able to program, and upgrade with the radio off, and the only connection as a UART.
But I'm both overwhelmed by the number of options (DFU, SMP, and...
Hardware: nRF5340DK
Software : nRF Connect SDK v2.6.1 (any reasonably up to date is fine)
Hi,
I'm new to Zephyr and Nordic and I want to make an example multi-core application...
We have a custom board based on the nRF52805 that does not have a HFXO or LFXO. We are using NCS 2.6.1.
When the firmware thread is idle, current consumption as measured...
Hi,
TLDR: Tried the new BLINFO feature on an existing app, upgrading to 2.6.1 SDK (Zephyr 3.5.99). App does not boot after merged.hex flashed.
So we are updating our project...
Hi,
I am trying to figure out how to change the automatic gain settings on the on-board microphone. It is connected via its I2C to the hardware codec, but apparently not...
Hi i would like to connect an led with mcu (NRF52832-QFAA-R7) and control the led with PWM. while investigating in datasheet i found "Three PWM modules can provide up to 12...
Hi there,
As I’m currently evaluating our GNSS implementation, I’ve encountered some discrepancies in your documentation.
My inquiry pertains to the optimal implementation...
I'm using 2 nrf52840dk, ncs2.5.0; running the central_uart and peripheral_uart examples, I want to know how to send a string without pressing the "enter" key. For example...
