Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Hello everyone,
I got a task which I try to implement using a NRF51822 iBeacon board.
The Task:
Advertise a Device and provide a mechanism to connect without traditional...
Hello, I'm working with the EK PCA10003, that has the NRF51422. I'm trying to read the information of the accelerometer MPU6000 with an ISP interface. At the moment I cannot...
I'd like to use the GATT/GAP driver from an ARM based Linux system. Is there any possibility of getting a library compiled for ARM or (cough) the source code to build it myself...
Hi,
Our application has a GUI, the UI data is stored in the QSPI flash and it is independent of the firmware,
We program the QPSI flash via the PC tool in the development...
Hi , I got my Nordic Thingy : 53 I wanted to connect other sensors to the Stemma/qwiic port of it . Can you share some documents or example of how to connect multiple sensors...
Hello, I have a problem regarding production flashing a nRF52811 device. We are using a Segger Flasher Compact, but I also tried a Segger J-Link Compact. To flash we are using...
We used 52840 chip to produce a near field communication module, the antenna is on board antenna, some problems occurred during the verification process, can your engineer...
hello Nordic
i work on nrf52832, trying to run it with zephyr application
one board runs fine (more/less, there are some MPU FAULT issue that i am facing with no luck...
Hi everyone,
I have some issue when my device is in very low temperature of -60°C / -70°C.
We use an NRF52832 (SDK 15) on modules (BMD-300 frome UBLOX formely RIGADO...
I'm working with lsm6ds33 sensor using lsm6ds3 driver I get some results, but they are ae rarely modified and didn't follow the IMU motion so how can I correct this.
(The...
Hello,
When I use sntp to get the timestamp from time3.google.com, getaddrinfo returns a -10 error. nrf9160 device also reboots automatically, why did the device reboot...
Power Profiler app v3.5.0 running in nRF Connect for Desktop v3.12.0 in Ubuntu 220.4 reports "No Supported Devices Connected".
I have used my PPK2 successfully recently...
Hello team,
I was not able to receive a suitable reply for this post for almost two weeks. I started thinking the engineer had gone for vacation. That is the reason I...
Hai, how you doing?
I am facing difficulty in trying to connect ble devices with windows 10. I am using BLE dongle APLIC WDP 304747 (Also tried another couple of BLE dongles...
In nRF Connect SDK 2.1.0 the devices in the DTS file are missing the "label".
For example, in nRF Connect SDK 2.0.0:
gpio0: gpio@842500 {
compatible = "nordic,nrf-gpio...
we are using NRF52840 , with a SD card. Data is stored in SD card in Text file or .csv file every 10 mins. We want to push the data to Mobile App either using the BLE or using...
about ANCS categoryID 12
I see this website
https://www.linkedin.com/pulse/working-ble-profile-apple-notification-center-service-sarda
have any one know
how to get...
Hi Nordic,
1. Dual Uart this code i used
2. Its working fine and am getting output also
3. But i have doute its printing from uart0 but i want from uart1
4. For that...
