Hi,
I am using the NRF8001 in UART mode and attempting to bond with my android device (Lollipop 5.0 Nexus 6).
i am using the nordic arduino sdk which is found here:...
Hi, I'm using the nRF8001 in an application that requires security so bonds to the remote client/central. My device supports firmware upgrades that may involve new nRF8001...
Hello.
Initially when reading the Gazell documentation I didn't think it'd be a problem but now in Keil seeing this has introduced some doubt whether it's a thing:
...
We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Note: This might actually be a documentation issue more than a real problem because the build seems to work. But some clarification would still be appreciated.
We're developing...
I'm developing FOTA through LTE Modem which is made from QUECTEL(EC21KL)
On my custom board, nRF52832 is connected with EC21 LTE Modem via UART bus(TX : P0.16, RX : P0...
I am updating Nordic Thingy:91. I am following instructions on Nordic's DevZone web page: "Getting NB-IoT Demo running on Thingy:91
I have successfully updated modem using...
Hy
i am using a nrf5349 Dk board ,i am able to build and flash the board.
but when i am using this by building and flashing the board with hci_uart .in the linux system...
Hy ,
After i a buildng and flashing the hci_rpmsg as a cupapp . i flash the board
Then when i am checking the board with ubuntu laptop .i am not able to see the board...
Hi all!
I'm currently working on the UART on the nRF5340 board. The SDK describes three options: -polling API,
-interrupt-driven API,
-asynchronous API. With Polling and Asynchronous...
During development I noticed the following behavior:
If NRF_SDH_BLE_GAP_DATA_LENGTH=251 and NRF_SDH_BLE_GATT_MAX_MTU_SIZE=185, on Android devices the connection procedure...
Hi
For some reasons my Windows 10 laptop reports two JLink CDC UART Ports when I connect one of my nRF52SDK boards.My plan is to use this board with nrf Sniffer / Wirshark...
Im struggling here with porting my code from SDK15 to NCS 2.0.2
Im happily TXing data from NRF52811 via UARTE and receiving via FTDI to PC, but Im unable to receive any...
Hello,
in the nrf connect application for mobile phone I can see the RSSI values being updated when scanning, but when I connect to my peripheral the RSSI info is not available...
Hello, I'm developing firmware for our custom board with a nRF9160.
The problem I'm having is that the modem crashes with error code 0x10 sometimes (read: about every 3rd...
HI guys I am working on nrf connect sdk v2.0.0, I am trying to modify periodic_adv example to stop changing mac address every time an advertising restart.
Hi,
I am writing the sample program "https_client" to the nRF9160-DK with Visual Studio Code's "Flash". I need to set the APN every time I write with Flash. Is it possible...
