Hello.
Initially when reading the Gazell documentation I didn't think it'd be a problem but now in Keil seeing this has introduced some doubt whether it's a thing:
...
We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Dear Sir/Madam,
We developeted a smart device based on nRF52840 chipset(to be more accuracy, we desgined our own module based on this chipset, then our end product use the...
I'm currently trying to change the host name of "https_client" and check the operation, but it doesn't work.
Even after changing the host name back to the original, "Waiting...
Hi,
We want to do provisioning of multiple mesh nodes using pb-adv procedure. we installed nrf MESH app, but we are not able to do provisioning for one node using Pb-adv...
Hello everybody. I'm designing a custom PCB fed by a typical 3.7 V nominal 4.2 V peak lipo battery, where minimal area and thus component count is a key factor. Aside from...
How can I adjust the BLE transmit (Tx) power, up to and including +8 dBm? I'm using nRF Connect SDK (NCS) on an nRF52840-DK .
I modified the throughput sample to reverse...
Hello, I'm trying to run the Ble Peripheral sample from "nrf\samples\bluetooth\peripheral_lbs" i'm using nrf connect V1.8.0 and NRF5340dk i followed the code in the github...
Hi,
I'am using the Ultrasonic Oxygen Senor with the nrf5340, the output is like this "photo" I want to calculate the concentration and the purity and with this values I...
Hello,
Is there any way to program the frequency output when sending a carrier wave to have a step size of around 1KHz? It seems that the default step is 1MHz.
Hi
I am trying to get the manufacturer data by ble_advdata_parse() as instructed in this case and this case , but it's not found in my SDK14.2, so how can I get the manufacture...
It's not possible to proceed a firmware update of matter light switch example on nRF5340DK.
I use following SDKs / Repos
nrfConnect SDK v2.0.2
standalone zephyr SDK...
Hello,
I have a component (AMC1306) in which I input a signal of at least 5Mhz. When this signal is triggered to this component, it sends me back data at this same speed...
Hi, I am trying with coap_client/server example programs on a custom board. I created a custom board for Zephyr and it is compiled without errors. I have a single button switch...
Module: nRF52832
Implemented pairing for ble_app_UART (NUS). However, I can connect with ble_app_uart_c, which does not have pairing implemented. Please tell me how to prevent...
I've just updated to the new V4.0.0 of the nRF Connect for Desktop BLE app. I'm trying to set it up as a server with CTS (but with both Current Time and Local Time Information...
