Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Hello everyone,
I got a task which I try to implement using a NRF51822 iBeacon board.
The Task:
Advertise a Device and provide a mechanism to connect without traditional...
Hello, I'm working with the EK PCA10003, that has the NRF51422. I'm trying to read the information of the accelerometer MPU6000 with an ISP interface. At the moment I cannot...
Hi,
I'm setting up nRF Connect SDK according to this instruction ( http://developer.nordicsemi.com/nRF_Connect_SDK/doc/latest/nrf/gs_installing.html) and Getting Started...
Hey,
in our project the nrf is acting as the central and connecting phones.
As part of the connection process:
1) We check if the phone is bonded in the nrf.
2) We...
Hi,
I'm on NCS 1.8.0 and I've successfully built and run the peripheral_nfc_example sample. Printed logs when reading NDEF message using a smartphone
When I came to...
I have a nRF52840-DK that stopped programing.
As a starting point to get it back to work, I reflashed the Interface MCU Firmware.
It is correctly detected by J-Link Configurator...
Hey Nordic,
My project is based on "ble_app_uart" and "ble_app_uart_c" examples. I modified them to some extent. You can download them from here .
Normally, I can write...
Hello!
On 3 and 7 of August my employee directed to you several questions regarding NRF. Case ID: 293339
Can I at least urgently receive the answer for the question in...
Hi,
We need to test our product for reliability when it comes to BLE connection in the vicinity of other BLE and WiFi devices. Do you have any suggestions on how to perform...
Hi all,
I am trying to use the bt_disable functionality on Adafruit Feather sense which has nrf52840 to restart a connectable BLE Service. The first call to bt_le_adv_start...
I'm developing an application using the NRF52840. I'm using the ADC, and there may be times where the signal to be measured is up to 1.8V, but the NRF52840 is not yet powered...
I am using the NRF52840-DK REV2 to program my custom board. I am using the debug out port and connecting it to my custom board, I tried both powering the custom board through...
Dear Nordic Engineers
I have a problem and would like to ask you about the I2C work state.
I read this link: https://developer.nordicsemi.com/nRF_Connect_SDK/doc/latest...
Hi All,
I am working with NRF beacon project currently, and I explored many other NRF connect SDK sample projects like, Ble peripheral, ibeacon etc. But I am unable to...
Hi,
I'm trying to implement FreeRTOS on nRF52832 using the S132 SoftDevice and SDK version 17.1.0.
This is meant to read multiple sensors at a configured frequency ...
Hello all,
I have managed to connect the BLE module, based on the nrf52820 via the SW (4 pins) to the nrf52dk and surprisingly programming works via the Segger EM !
Indeed...
Hi,
I would like to carry the full modem update. Based on nordic website I need at least 4MBytes of flash for doing a full modem update on the nRF9160:
https://developer...
