Hi,
I am using the NRF8001 in UART mode and attempting to bond with my android device (Lollipop 5.0 Nexus 6).
i am using the nordic arduino sdk which is found here:...
Hi, I'm using the nRF8001 in an application that requires security so bonds to the remote client/central. My device supports firmware upgrades that may involve new nRF8001...
Hello.
Initially when reading the Gazell documentation I didn't think it'd be a problem but now in Keil seeing this has introduced some doubt whether it's a thing:
...
We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
I am developing a project with nrf mesh SDK 5.0.0, I use dimming code, but the code uses rtt input, if I want to replace rtt with buttons, what should I do? I'm learning,...
Hello! I will try to make this as simple as possible with the details regarding this issue What I have
nRF52840 DK (pca10056) (As BLE sniffer)
nRF52 (pca10040) (Used...
Hello
We are using NRF9160 AssetTracker 1 and MQTT to AWS. We have a AWS Certificate, Root Certificate and Public and Private Keys on the device.
We want to start testing...
My device get deep sleep mode. It wakes up from reset button trigger. Because I couldn't gpio pin trigger for wakes up. So I put vibration sensor to reset pin. It wakes up...
Hello, I am developing a custom board based on nRF52832 that should spend most of it's time in SystemOFF mode. Eventually, it will wake up on an GPIO event caused by the external...
Hi,
I've been using the DWT macro cell successfully on the app core to provide high accuracy timing information. E.g., with these declarations:
and enabling the cycle...
hi ~
peripheral can bond how many smartphones ?
and What will happened if over bond?
i use sdk12.2 below 'is my setting
#define SEC_PARAM_BOND 1 #define SEC_PARAM_MITM...
Hi…
I am using freeRTOS V10.0.0 release
I am using nRF52820 + SDK V17.0.2 with SD112 V7.2.0 along with tickless idle as this is a battery based product…
When my application...
Hey guys, I'm an embedded software engineer and I am currently working in a prototype, specifically using the Circuitdojo Feather nRF9160 , I am also using a Hologram International...
Based on the Sample "Bluetooth Peripheral_uart:
My latest attempt to send long data stream:
I send:
1234567890123456789012345678901234567890123456789012345678901234567890...
Hi,
I've met a problem. It seems NVS sometimes erases sector during initialization.
As shown in following log, I wrote 2 datas(address, slot) in NVS. Normally, I can read...
Using the period required for 2Mbps Gazell, 600us, how much does this slow down BLE (bandwidth/# packets)? Also, does the timeslots API work well with nrf52? If I modify this...
Solved, just bad luck, I got 3 broken module, the 4 is ok.
So it module's problem.
======================================================= I am trying to flash "hello...
Hi,
is there any way adjust the ISO channel transmission power (e.g. -20dBm, +2dBm, ...) in the new nRF5340 Audio application? I saw that one can select between 0dBm and...
