At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Hello everyone,
I got a task which I try to implement using a NRF51822 iBeacon board.
The Task:
Advertise a Device and provide a mechanism to connect without traditional...
Hello,
I'm currently trying to convert the SPI example project for NRF52811 for the EVK BMD-360 and ran into an issue.
I'm using segger embedded studio 5.42a and nrf sdk...
Hello Nordic Dev Zone,
I have been developing on the nrf5340pdk and recently switched to the nrf5340dk.
I utilized the COM console output for app/net cores via the `minicom...
Good day,
I have successfully implemented exercise steps 1 to 5 of Exercise 2, Lesson 3 of the DevAcademy "nRF Connect SDK fundamentals" course, that deal with "adding custom...
Hi,
As i2c communication + computation takes 45ms in my timer interrupt that happen each 100ms and gave issue with SD, I decided to set a flag in the interrupt and execute...
Is there a configuration / sample available of mqtt simple to talk to the mosquitto server using an authenticated client on port 8884? I saw a message on here that was about...
Hi,
I want to get the GPS value from A- GPS continuously.
Meanwhile, if there is any new application firmware version update,
I would like to download the image with...
I see the problem here. use the dfu-util command in the window system
and i tried many methods and failed The following is my reference website
http://zadig.akeo.ie...
I've been playing around with some code that puts my hardware into System OFF mode to save power, and then will exit this mode and start up when one of three different GPIO...
Hi,
https://github.com/NordicPlayground/nrf52-ble-app-uart-c-multilink
I have tried the example you modified. It works fine. However, I get ERROR 17 NRF_BUSY when 2-3...
Excited to have ordered my BLE Audio DK which uses NRF5340.
In my use case I am looking for many microphones (audio transmitters) to a single listening device (audio receiver...
Hello!
I am working on a medical device project utilizing nrf52832 microcontroller. We use a mobile app to control and interact with the device through BLE since the device...
Basic Bluetooth connection question
How do advertisements usually work? So I have earbuds and a phone. When I pull the earbuds out of the case they auto connect to a bonded...
Hi All!
I am using nrf52820/33 and am able to successfully connectable advertise (coded PHY) by nrf5 SDK. Now I want to use NCS (Zephyr RTOS) to do the same job . Can...
Hi! I'm trying to use the nRF Connect App on a M1 Mac. I keep getting the error shown above with my Jlink connected.
This is the output of the nrfjprog cli tool:
How can...
Hello,
I have been experimenting with the direction_finding_peripheral sample in the nRF Connect SDK. I have been trying to connect to the peripheral using a custom device...
