Hello.
Initially when reading the Gazell documentation I didn't think it'd be a problem but now in Keil seeing this has introduced some doubt whether it's a thing:
...
We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
I have successfully run, Nordic serialisation connectivity application on nrf52480, (And able to control this from a custom board, and also from PC). But I want to use a lighter...
Hello !
I'm currently working on a project using the DK Boards nRF52832 .
I'm disappointed that one card no longer works ( doesn't light up ). I therefore explain to you...
Hello everyone :)
I'm trying to get an analog signal from n channels. I started with modifying the battery sample from Vdd to AIN0 according to the modification - only to...
I am using Nordic Serialisation library, with a nrf52480 chip as connectivity chip and a m4 arm core custom board as Application chip. I am able to establish gap connection...
Hi,
I am trying to enable the internal clock for NRF 52832 (BMD-350) module.
The configuration option for the clock has
1. RC Oscillator
2. Crystal Oscillator
3...
Hello,
I am using the nRF52840 DK to debug my application using nRF Connect SDK v2.0.0 ..
Application runs well in debug.
But when click restart / reset .. it should...
Hi Team,
I am working on NRF52832 based on the BLE mesh protocol here I am using the Light_switch example of SDK - nrf5sdkformeshv500sr
Here I transfer boolean(0 and...
Hi, I'm developing an application based on ble_app_uart, and integrate FOTA is the last feature. I'm using sdk16, S140, nRF52833. I plan update firmware over BLE, so I have...
We've a custom board which has NRF52833 and TM52F1376-MTP-C3. They are connected over UART.
What I want is transfer binary data between Phone and nRF52 over BLE.
and then...
Hi Nordic team,
I'm going to start new BLE application project, so I tried to understand how to use nRF52 series first.
I completed the academy and I'm trying to make...
I am attempting to compile the peripheral_uart example targeting nrf52840dk, I've done quite a bit of work with zephyr but never with the nRF Connect SDK. I've encountered...
Dear Nordic,
There is an issue with simultaneous RTT shell and logging on nCS 2.0.0, please check the screenshot.
Althougth CONFIG_LOG_BACKEND_RTT_BUFFER=1 setting is...
New to Zephyr it has been reasonably straightforward building the UDP sample application to enable an nRF9160 dev board to send and receive UDP messages via NB/IoT to/from...
1. I want to run asset_tracker_v2 in thingy91 kit.
2. I want to interface two UART external devices to thingy 91, may the pins of nRF52840 be used ? if yes, in asset_tracker...
