I am working with the nRF8001, and I'd like to create a services.h file that will let me broadcast battery level and as well as allow temperature to be read by a peer.
...
Hi We have an application where we what to read i2c sensor data over the air to an iPhone. We've taken ble_app_uart_S130 project and grafted in some twi_hardware code. There...
I am interested in the S130 ability to hold 3 central -> peripheral links over BLE, and am looking for some evidence that this has been accomplished with extremely low-power...
I'm trying to implement channel scanning in our nrf24lu1p based USB dongle.
I'm following the specs and basically loop though each channel ;
loop
stop listening
set...
Hi,
I am using the NRF8001 in UART mode and attempting to bond with my android device (Lollipop 5.0 Nexus 6).
i am using the nordic arduino sdk which is found here:...
Hi, I'm using the nRF8001 in an application that requires security so bonds to the remote client/central. My device supports firmware upgrades that may involve new nRF8001...
Two Factor Authentification is enabled for my primary account (I had to create a second one to ask question).
Something has gone wrong with setting up two factor authentification...
I wanted to implement a time sync feature on nRF-52840 DK. I took a reference from this example, but there were certain things unclear to me.
Can somebody explain to me...
Hello. I am developing a central operation using nrf52832 (S132 v7.0.1, SDK v17.0.0).
There is a numeric comparison as an authentication method, can I do it with sdk17.0...
Hello,
I'm new with Nordic products, and I'm trying to use my New dev kit nrf5340 DK.
The request today is about my code, I implemented my code in the DK, and now I want...
i have nrf52832 and softdevice s132. i want to calculate throughput. i tried running ble_att_mtu_thorughput example and read https://www.novelbits.io/bluetooth-5-speed-maximum...
Hi,
when debugging BTmesh (with MPSL) breakpoints trigger an assert. This is listed in the known issues of the nrfConnectVScode page:
https://nrfconnect.github.io/vscode...
Hello, i'm trying to flash a code in my module nrf52805 thx to my Dk nrf52840. i have this error I followed the instructions here: https://devzone.nordicsemi.com/guides/short...
Hello,
I want to build a configuration where MCU Boot secondary partition is in the external flash and QSPI data encryption is turned on.
I modified the nrf_qspi_nor...
Dear, I want to interface nRF5340 to normal 16x2 Alphanumeric LCD running on 5 Volt. Are the Port pins of nRF5340 5 Volt compatible when nRF is running with 3.3 Volt supply...
Hello,
After succesfully configuring the W5500 driver using Zephyr, I am trying a few examples in the given samples (socket echo). I am unable to send or receive / ping...
On the nRF5340 P0.00 and P0.01 are used for the 32.768 kHz crystal by default and are not available as GPIO on the connectors.
how to remap this pins to gpio?
I need to develop a pair of BLE-capable devices that talk to each other. The communication between them will be very simple - the central needs to tell the peripheral the...
Hi,
When the NRF9160 boots the GPIO level of a given pin, such as P12, is set to high (3.3V) before the main application gets a chance to call gpio_pin_configure and gpio_pin_set...
I am now using the DFU functionality to upgrade the code combined with the CoProcessor and radio_test samples and find that the code takes up too much space to upgrade. I...
I recently bought Thingy:91 (nrf 9160) there was a SIM card included but it didn't work! I have written to support twice at the recommended address [email protected]. it was...
