Hi, I'm using the nRF8001 in an application that requires security so bonds to the remote client/central. My device supports firmware upgrades that may involve new nRF8001...
Hello.
Initially when reading the Gazell documentation I didn't think it'd be a problem but now in Keil seeing this has introduced some doubt whether it's a thing:
...
We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
In the nRF SDK 15.2, I am using the function idle_state_handle() which has a macro NRF_LOG_PROCESS() which is defined in another header file as NRF_LOG_INTERNAL_PROCESS()...
Hi all,
We've been trying to transfer data from 52840 custome board to android device via USB.
52840 device could be detected after connection but it cannot be accessed...
Hi,
I am looking for usb connect and disconnect events to be able to trigger some behaviors in our product.
I don't find any API for that, like subscribing via a callback...
Dear Members,
I tried to compile :
E:\nRF5_SDK_17.0.2_d674dde\examples\ant\ant_broadcast\tx\main.c
I got this error :
..\..\..\..\..\..\..\components\libraries\util...
Dear Members,
I want to port a code from :
E:\nRF5_SDK_17.0.2_d674dde\examples\ant\ant_async_transmitter\main.c
to be used with PCA10056 ?
Any ideas ? thanks
Hi,
I have following questions
1. How to define the limit for number of bonding information stored in internal ROM of nrf52832?
2. We want to verify the bonding functionality...
Hi Sir
We have a project with nRF5340,
Coz our product will be a smart watch, we will need to re-programming our product after full assemble in production line,
So,...
Hi all
We observed a strange behaviour with mcuboot / bootutil in our nrf9160 based project.
The bootloader log messages showed that something with the primary image is...
I run the ./nrf/samples/bluetooth/peripheral_uart example on 52840DK and connect to it using the nRF Toolbox UART section.
The connection works and I can send messages to...
Hello,
I want to modify the lte_ble_gateway app (nRF connect SDK 1.6.0) to connect with the nRF52DK advertising through the ble_app_uart (nRF 17.0.2) application. The lte_ble_gateway...
Hello,
I am trying to test 1 central 4 peripheral multilink(with saadc).
However, when the master-slave(central-peripheral) is connected,
the connection disconnected...
As the title states, my program (and a simple idle/hello world program for that matter) pull approximately 600-800 uA at idle. Same exact program, driver, and config on my...
Hi all, I am trying to write a driver for a TMP116 temp sensor based off the existing Zephyr TMP116 driver. I have added in functionality to enable the interrupt pin to enable...
