At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Hello everyone,
I got a task which I try to implement using a NRF51822 iBeacon board.
The Task:
Advertise a Device and provide a mechanism to connect without traditional...
Good Afternoon, Im using a samsung galaxy tab a - Model num SM-T510 Android Version 10 nRF Mesh app version - 3.1.5
After provisioning 14 nodes, whenever i try to reset...
Hi,
I am trying to integrate UART and DFU serial from the mesh example.
What I did is:
1. Adding uart drivers and libraries into the DFU project.
2. Adding codes...
Hi,
We are seeing the issue mentioned in https://devzone.nordicsemi.com/f/nordic-q-a/20291/offset-in-saadc-samples-with-easy-dma-and-ble/79053#79053 . We have 2 sensors...
Hello, I'm getting started with FreeRTOS in Nordic SDK 15.3 I have created a small test code, using binary Semaphore from FreeRTOS, that waits signal from SAADC callback....
Hi, I want to do some modification in the existing nrf connect sdk sample projects. I did some modification in prj.conf and CMakeLists.txt file. But now I am not able to load...
Hello,
Could please someone suggest to me the 10 POS debugging header(5*2) with 1.27mm with a lesser size footprint?
I need a lesser pad size so I could place it on my...
i have a custom board with an nrf52840, i use a J-link programmer to flash the chip with the nrf connector programmer app.
I am able to read the memory and erase the chip...
Hello fellow bit jugglers!
We are developing an application for a nRF52805 on a nRF52-DK board, using NCS.
NCS version: 1.5.1
Zephyr version: 2.4.99
BLE controller...
Hi,
I want to run the Thread MQTT-SN Publisher and Subscriber example using the nrf52840 DK and the nrf52840 Dongle I have on hand.
I was able to sucessfully build and...
Hi, I'm trying to use BLE/Thread Multiprotocol for BLE RSSI scanning and send values using Thread, is it possible to use BLE and Thread(FTD) concurrently with out time-slice...
Hi all, Using SDK 17.0.2, on a Laird BL653. I've been messing with creating variable PWM sequences and found an issue where a 100%->0% duty cycle transition does not occur...
I once used nRF Sniffer with my nRF51822 module. I see that everything has updated since - Wireshark, Sniffer plugin (now is Python 3.4+), Sniffer firmware. As I can see,...
