I am interested in the S130 ability to hold 3 central -> peripheral links over BLE, and am looking for some evidence that this has been accomplished with extremely low-power...
I'm trying to implement channel scanning in our nrf24lu1p based USB dongle.
I'm following the specs and basically loop though each channel ;
loop
stop listening
set...
Hi,
I am using the NRF8001 in UART mode and attempting to bond with my android device (Lollipop 5.0 Nexus 6).
i am using the nordic arduino sdk which is found here:...
Hi, I'm using the nRF8001 in an application that requires security so bonds to the remote client/central. My device supports firmware upgrades that may involve new nRF8001...
Hello.
Initially when reading the Gazell documentation I didn't think it'd be a problem but now in Keil seeing this has introduced some doubt whether it's a thing:
...
We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
Hello everyone,
I am currently in the process of designing a prototype using the nRF9160 and I use the Nordic-Thingy91 as a reference for some parts. The Thingy91 uses the...
Is there any supporting documentation or information about remote assignment of receivers.
The only reference I have been able to locate is sparse and not backed by anything...
Hi guys,
I'm pretty new in embedded development without using an Arduino. I tried to use the sensor APIs of BMI270 and BMP388 recently, but didn't get it to work.
The...
HI All,
Could you please share the details for the below s on Nordic controller MCU nRF52833-QDAA to receive quotation on BLE_SIG certification,
QDID for Link Layer...
Hi,
I have a custom board running with the nrf52832. To program it I'm using the nrf52DK board with the PCA10040 and the bootloader is based on the one found in examples...
DK : 52840
case :
we make 52840 enter active scan state and know other broadcaster devcice mac,
can we use scan filter policy filter this broadcaster devcice ,and only...
(1) I connected Nordic nRF52810 device to ipad (version: 13.5.1) (ipad uses app for connection). At this time, a pop-up window appears asking if I want to pair the devices...
Good morning. I want to take ADC 12bit/1k sampling input and send uart and bluetooth. uart works fine, but there is a problem with losing data in bluetooth transmission. ...
During testing of various combination of BLE Mesh Provisioning, I found a couple of bugs in dk_prov.c
If you Disable all OOB options for no OOB, it does not work properly...
I'm using nrf_pwr_mgmt_shutdown to shut down the system to wake on interrupt. 17.0.2 SDK and 7.2.0 softdevice. When I step through the code with a debugger, it gets to sd_power_system_off...
My device is powered by an electromagnetic field from the 10 kilovolt line, which cannot deliver much power. When connected to a zigbia network, nrf52840 consumes too much...
I want to receive only 1 byte (Master in Slave out) without sending any bytes using using SPI. However when I monitor the SPI clock it produces 16 clock pulses. Although my...
Hello, How do disable code optimization in SES Nordic Edition when using nRF Connect SDK? I can't find "Options - Code Generation - Optimization Level" as when using nRF5...
Dear Sir,
I am trying to run example with NRF91 DK MQTT simple and I am able to connect with LTE network. as shown in below screenshot.
But as shown in the screen...
Hello, All
I go through datasheet of nRF5284o QFN73 IC. But i can't found which pins are used as uart /spi/i2c/pwm/timer/ I2S in pin description. Because pin assignment...
