Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Hello everyone,
I got a task which I try to implement using a NRF51822 iBeacon board.
The Task:
Advertise a Device and provide a mechanism to connect without traditional...
Hello, I'm working with the EK PCA10003, that has the NRF51422. I'm trying to read the information of the accelerometer MPU6000 with an ISP interface. At the moment I cannot...
Hi,
I am evaluating Zephyr mesh and implemented two timers; one triggers at every 2 mS, the other triggers at every 500 uS.
I put a code in both timers' events to toggle...
Hi, Our platform is NRF-52833 Our project use RS485 bus (nordic's uart + a 485 chip) to communicate with other device. And we choose the libuarte to be the uart handler to...
Hi,
In the nRF_SDK_for_Thread_and_Zigbee_v4.1.0, in examples/thread/NCP/radio folder, there is no option for compiling the firmware for PCA10059.
I want to run RCP firmware...
Hello guys,
I'm trying to interface ds18b20 temperature probe and I'm using this code , In termite its showing output as -0.062500 I don't know why can anyone tell what...
Hello,
I'm using NCS 1.4.99 with a nRF5340DK and want to use the hardware CS of the SPI and also use BLE.
Here is a simple code that work on a nRF5340PDK but only work...
Hi All,
I was just reading the white paper on RF testing guidelines, and I noticed several times there have been mentions of "nRF Performance Instructions" for each of...
Hi,
I am working on NRF52832-based board, with SDK 15.2.
My BLE device is protected with Legacy Connection OOB preshared key.
I would like to use Android NRF Connect...
Hello dear,
I am installing Embedded Studio on OSX (Catalina), and I following the nRF Connect step... all goes fine, but when I try to use "Open nRF Connect SDK Project...
I'm trying to see debugging info with nrf51 dongle.
As far as I can tell I just need to use:
#define NRF_LOG_MODULE_NAME "APP"
#include "nrf_log.h"
#include "nrf_log_ctrl...
On a nRF5340 DK the sample ncs/zephyr/samples/subsys/usb/cdc_acm runs fine. However, if I add "CONFIG_NO_OPTIMIZATIONS=y" to prj.conf I get faults (see below). Any ideas why...
Hi,
I am preparing Windows desktop application which will use nrfutil for DFU of the products (containing secure dfu bootloader). I tested nrfutil v6.1.0, v6.0.1 and even...
Hii guys,
I am trying to establish communication between two nrf52 module.
My application is as following
1. I need a central device which can work as master and remains...
Hello, I am stuck initalising both TWIM and UARTE. I am focusing on the TWI Scanner example but using TWIM instead of TWI. No matter what I do I cannot get past the initalisation...
