We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
I need to monitor how much heap was ever left available, as a minimum, after I have run my CI test suite. This is the true minimum heap ever remaining, so taking account of...
Hi -
In reading through the data sheets for the Nordic chips that support the low-rate (125 kbps) BT 5 PHY, I'm seeing Rx sensitivity numbers around -103 dBm. For the 1...
Hi,
To manufacturer production I would like to use the nrfjprog.dll in order to make an WPF C# application to program our NRF device.
I would like to use your nrfjprog...
Hello,
I am working with the nrf52832 chip and wanted to know if there are any pins that are shown on the schematic diagram, that I should not use to ensure that the Bluetooth...
Hi there,
In my application I need to send varying amounts of data (1~8KB) and store it in RAM. I trying to use memory manager library to replace the malloc() and free(...
Hi there,
I'm having some trouble piecing together an app to use V2 of the NRFX SAADC API, compounded with this being my first time using the SAADC functionality on an nRF...
I've tried to update the firmware on my Thingy:91 to version 1.2 using the file mfw:_nrf91060120.zip:
I set the Thingy:91 to ' application serial recovery mode by pushing...
I tried to play with nrf52840 and ade7953 .
At the begining, I use PC uart application to do the following test and everything works well. Here are the testing steps: 1...
I have the CLI module over UART enabled, with one command that continuously prints out the readings from a sensor. What I'm trying to do is stopping this continuous printout...
Hi,
I am using the nRF52832 and am going at it barebones because I cannot for the life of me get the SDK to work. I am using the nRF52832 manual.
-> Manual
I have two...
Hi, Im using a nRF52DK to read LIS3DH accelerometer readings in putty. Im new to this platform, I tried couple of example programs like blinkey, uart, and button in BLE. Now...
Dear All,
I am trying to implement a simple data recorder on nRF52840 DK that digitizes signals over SAADC and writes them onto the SD card. The program is working fine...
Hi,
Does anyone know where to find the BLE backwards compatibly of a given soft-device ?
I have looked at the PDF document given for my soft-device version S132, and...
Hello,
I am running an application on the s140 soft device using the buttonless dfu as an example. I am using the dual ramp pwm scheme to generate complementary pwm waveforms...
