We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Hi.
I am a student studying esb examples with nrf52433 board.
1. If data is sent from ptx to prx using static payload, is tx completed without receiving ACK? Don't need...
Hello,
I try to measure the current of the nRF SoC on my NRF52-DK, by using an oscilloscope and USB as a power supply, related to the guide from Nordic from here:
https...
Hi,
I need to write a 32-bit value to an NVM flash page whenever my code hits an assert failure. This failure can occur anywhere in the code - my application, the Nordic...
Hello,
I'm working on a circuit which has a pin connected to a pull-up resistor, using the nRF52 DK and SEGGER Embedded Studio 5.20 to develop the software.
This pin is...
Hello everybody, I am using Zephyr with the nrf52840-dk device. I would like to store the DTLS credentials with a secure way. I don't want to be part of the code and thus...
I have been testing out HTTPS with the http_application_update .
I have been able to successfully setup a TLS 1.2 connection, but I was seeing a lot of "Peer closed connection...
Hello
I would like to modify my Transmission Parameters of my Thread network. According to the CoAP protocol ( https://tools.ietf.org/html/rfc7252#section-4.8 ), it is possible...
Hi Dev Team,
I am trying to measure the low power performance of the nrf9160.
For this, I tried to use the "system_off" example in the folder : C:\Users\adeel\ncs\v1.4...
Hi,
I'm trying to alternate between the beacon sample and the central sample in one application. It builds and initiates, the connection example from central is functioning...
Hello everyone, this is my first time participating in the forum. I am a very new hardware and firmware developer (this is my first job in the industry of iot). I have chosen...
We are currently evaluating external memory on the NRF52840 and are trying to use external memory within the memory space of the processor (XIP). We are aware of the erratas...
Hi, I am using nrf52840 as a peripheral. How can I use more than 1 uart(1 for GSM,2nd For GPS, and 3rd for show data in PuTTY). Which pins I can use for this? and how? any...
Hi,
We have a requirement where we need to store some application parameters (Eg. APN name ) in the nrf9160 flash. This parameters will be storing during production time...
Hi,
1. I was trying to measure the Bluetooth throughput of nRF5340PDK using the sample from ...\ncs\v1.4.0\nrf\samples\bluetooth\throughput, but from what I see in the requirements...
