At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Hello everyone,
I got a task which I try to implement using a NRF51822 iBeacon board.
The Task:
Advertise a Device and provide a mechanism to connect without traditional...
Dear Sir,
I am working on NRF52 and I have DK of PCA10040 / V1.2.1 / 2017.36 / 682236729. I have done program advertising with scanning both in one program. then I used...
Hi, I have problem. My NRF52832 Dev board is not recognizable by anything. L05 diode is blinking every 0.5 sec. I used Segger - not recognized, Keid again J Flash same story...
Hi,
I'm developing a BLE mesh project using Mesh SDK v4.2.0. I want to change the Tx power of the product in real-time, e.g. from 0dBm to 4dBm, 4dBm to 8dBm.
I've read...
I have an application that is running for a while and then it crashes.
Execution goes to softdevice_fault_handler(), calling it with parameters: id=1; pc=0xf764; info=NULL...
hi all
A silly question here , I am prepare to meet some security compliance , one of them is about delete files permanently.
I wonder how to get this done on nRF51822...
Hi,
I would like to wake the nRF52840 SoC from sleep via a GPIO High Pulse input.
What is the minimum allowable pulse period do I need for it to successfully wake up...
Hello,
I have the following application code (based on the template project from the SDK):
The receive callback is working and I get all the characters from my terminal...
From the datasheet I understand that any pins in port0 can be used as SPI. But I tried using the pins defined in nrf-sdk here and but there is no response. After searching...
Hi!
I am kind of DIY person and have a lots of time in COVID, I am a beginner to Nordic family, few months ago I implemented MPU9250 with NRF52832, I was able achieve...
Hi !
I am working with nRF52 DK to drive the nRF52832 and a sensor of Maxim Integrated.
I am using an older version of the SDK (14.2.0) because i need to modify an old...
Hello,
I was looking at power profiler (just playing with it) and I run it without proper setup on nrf52840DK, after that It seems that dk does not execute any application...
My application is again having troubles with opening an AF_LTE socket. It hangs indefinitely on the call to socket(AF_LTE,...). This code has been running successfully at...
i use nrf51822 and uart project
i need disable only RX when tranmitsion and reuseable when tranmistion complete. i tried
//NRF_UART0->ENABLE = UART_ENABLE_ENABLE_Disabled...
Hi
Do any of the Soft Device versions support the periodic advertising feature which is part of extended advertising and involves AUX_SYNC_IND PDUs? I looked at the API...
