Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Hello everyone,
I got a task which I try to implement using a NRF51822 iBeacon board.
The Task:
Advertise a Device and provide a mechanism to connect without traditional...
Hello, I'm working with the EK PCA10003, that has the NRF51422. I'm trying to read the information of the accelerometer MPU6000 with an ISP interface. At the moment I cannot...
According to the Online Power Profiler , the Standby time between Crystal start-up and Start radio is ~1 ms; however, we measure a variable amount of time between 0 s and...
HI All,
i m new to this technologies.Now m using NRF52840 DK and sdk as nrf15.2..we have developing the nrf52840 as a beacon scanner to scan the ibeacon details like rssi...
I'm using a Nordic dev board (PCA10040, nRF52832) with modified "Nordic_HRM" firmware sending packets of 20bytes at 100Hz over Bluetooth Low Energy.
I'm using Nordic's heart_rate_collector...
Hello everyone! I have followed the tutorial " Installing a 6LoWPAN enabled Linux kernel and required modules" and i have compiled the UDP client IoT example in order to test...
Hi everyone,
I am using nRF52 which has 52832 on it. Currently, I am working on 2 nRFs and one RPi with MQTT on the softdevice 132. One nRF is the publisher, another one...
I am using pcaboard10028 ,sdk12.3.0 and softdevice s130. I am using proximity example to read battery percentage level,so giving adc input as following:
channel.config.config...
Hi, I'm having problem with UART communication. I use basic UARTE code and I want to send simple data to PuTTy terminal. The problem is whatever I would send i get only 'K...
Hello!
I'm trying to update the bootloader of a nRF52 device OTA. We are using SDK 12.3. The device has our own application flashed, along with what is essentially the bootloader...
Hi Sir,
We want to know about AoA /AoD applications for 52811, and there are some question as below.
1. Is there a difference between BT 5.1 and BT 5.0 from the perspective...
Hi,
I'm implementing quadrature encoder to read motor speed/position. So far I configured a gpio pin where A channel of the quadrature encoder is connected to capture timer...
Hi, I'm now using nRF52DK with Keil and have followed the getting start manual in the Nordic Devzon.
Till now, I completed UART example and want to add ADC function to this...
Hi,
I wanted to know what is the recommended way of data transfer through ble if there are multiple sensors. Is Creating one service with multiple characteristics a good...
Hi everyone,
I am using SDK 15.2 with keil microvision and softdevice132 nrf52_6.1.
In version 13, system dispatch event was regestired with Softdevice handler as below...
