Hi,
I am using the NRF8001 in UART mode and attempting to bond with my android device (Lollipop 5.0 Nexus 6).
i am using the nordic arduino sdk which is found here:...
Hi, I'm using the nRF8001 in an application that requires security so bonds to the remote client/central. My device supports firmware upgrades that may involve new nRF8001...
Hello.
Initially when reading the Gazell documentation I didn't think it'd be a problem but now in Keil seeing this has introduced some doubt whether it's a thing:
...
We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hi!
We are developing an IoT device using the nRF52832. 2 years ago in this thread, https://devzone.nordicsemi.com/f/nordic-q-a/27099/nrf52832-ble-certification-under...
I'm combing over the CLI peripheral example, but having a few problems when running the example:
The Debug Terminal in SES blacks out the test so its difficult to see...
Hi I have developed and Android application to connect for 2 BLE Devices one after other.
These 2 BLE devices connection and service discovery will happen one after the...
Hi Nordic,
I am using SDK 12.3.0, S130 2.0.1 and PCA10028 nrf51 DK.
I would like to ask if central can make connection request without scanning (central know the mac address...
Hi everyone,
I have migrated my project from SDK for Mesh v2.1.1 to v3.0.0.
I am getting a Mesh Assert when the Mesh is trying to request a radio timeslot after the "NRF_EVT_RADIO_BLOCKED...
Is it possible to run Eddystone example from SDK12.3.0 on nRF51822 xx aa chip?
In the eddystone documentation it mentioned that S132 softdevice required, but on older SDK...
Dear Nordic,
Hi,i'm looking for an easy way to make Wlan coexistence with Ble,i know there has a solution that named 3rd party, just like this:
So, What i want to...
when we pass the BLE event handler as a function argument to BLE stack init function and register the function results in a deadlock mechanism. Is that we cant able to register...
Hi Guys,
I have a general question to the mesh functionalities. We built a mesh sensor network and I now want to now if it is possible to decrease the data-rate to increase...
Hi,
I just completed the migration from mesh sdk 2.2.0 to 3.0.0.
After running the project it get stuck at line 422 of timeslot.c in function timeslot_sd_event_handler...
Hi all,
So I've developed a custom board with the NRF52832 qfaa e1 and using Mbed OS 5. System on current is around 3.5uA when not using BLE.
When using BLE my idle current...
I'm learning NRF51822.Now,I want to develop it with PC.I need connected Nrf51822 & PC with Ble.What tools can I use? .I designed a Nrf51822 pcb based on CH340.
Hi,
I am using nRF52840-QIAA-T in my design. I am curious to know if Engineering B modification is implemented in the mentioned package.
Thanks in advance.
Hi i used nRF52840 Preview-DK and i try many example with SDK provided.
the problem is the range of transmission too short . can you help how to set power transmission of...
