Hi,
I'm using redbearlab's nrf51822 board. It is a arduino compatible board and hence it is using 0,1 (mapped to 9 and 11 for nrf51822). How do I make printf print to this...
An external PA/LNA is used to extend range of nRF51822, and S110 is used for BLE, How to switch between PA and LNA? and how to disable PA/LNA when there isn't transceiving...
Hi...
Can anybody help me to run ble_peripheral example (ble_app_hrs for S130). I have build and load the code successfully but cant see the advertisement. But while debugging...
I am working with the nRF8001, and I'd like to create a services.h file that will let me broadcast battery level and as well as allow temperature to be read by a peer.
...
Hi We have an application where we what to read i2c sensor data over the air to an iPhone. We've taken ble_app_uart_S130 project and grafted in some twi_hardware code. There...
I am interested in the S130 ability to hold 3 central -> peripheral links over BLE, and am looking for some evidence that this has been accomplished with extremely low-power...
I'm trying to implement channel scanning in our nrf24lu1p based USB dongle.
I'm following the specs and basically loop though each channel ;
loop
stop listening
set...
Hi,
we have developed a board that is using the nRF24LE1 chip. For test purposes I do want to toggle every possible pin. My first step is to develop this simple test code...
Hi all,
I am on the DK-52 with the SDK 13.0.0.
After erasing the device, I follow this steps:
upload the softdevice
nrfjprog --reset --program s132_nrf52_4...
Hi Forums,
I work 51822 custom board.
I try to add Buttonless DFU so I test the "experimental_ble_app_buttonless_dfu" compile is good.
But flash to the board can...
I am building a Bluetooth Mesh network with multiple types of devices.
The provisioner is now capable of provisioning and configuring multiple instances of Device A but i...
I am using nrf52832 with softdevice s132 v3.0.0, sdk 12.2.0 and FDS.
I am using sdk_config.h to configure various modules in my project.
Earlier config: Using Timer1...
Dear nordic devzone,
When trying to build the "ble_app_hrs_c" example project it does not build in SES.
Output/ble_app_hrs_c_pca10056_s140 Debug/Obj/peer_manager.o:...
Hi,
I'm currently investigating the Bluetooth mesh using the SDK for mesh alpha 0.10.0, I was wondering about the limitations on the re-transmission of messages. The current...
this issue might also be one of others than myself
my main development environment is based on linux ... firmware, QT, android and whatever comes along ... i used to write...
Is there native support for hardware coex lines? If we have a WiFi chip that produces a TX Active signal, can we hold transmit from the nRF52840 till that transmit is finished...
I have bought a Tayio Yuden EYSGJNZWY Bluetooth module, which is in fact just a Nordic's nRF51822 (256KB Flash and 32KB RAM) with added antenna. Tayio's files say that the...
Hi,
I have built an application which is based on BLE and protocol that supports high frequency sampling of sent messages. I tried to achive that using only BLE, but it...
Hello,
I am designing a custom board with NRF52832 IC. I have a query regarding routing of traces.
In my design, I am not using all pins of IC. Do I need to route traces...
Hello,
I am designing a custom board with NRF52832 IC. I followed the same layout design as suggested by Nordic.
But , I made some additions to reference layout. I added...
I'm trying to set up a gazell device with a channel table that is 16 channels long. This is for a pairing application where the host has a channel table that is 6 channels...
