Hello.
Initially when reading the Gazell documentation I didn't think it'd be a problem but now in Keil seeing this has introduced some doubt whether it's a thing:
...
We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
I'm trying to use Adafruit LSM6DSOX (I think it's a misprint and it's actually LSM6DSO), regardless. I can get it to work using I2C but I need it over SPI.
I have been racking...
Hi,
I am working on a board combination of nrf52840 and HL7800 modem. So, I just migrated from 3.6.0 zephyr to 3.7.0 and ncs 2.7-branch.
modem driver: https://github.com...
Hello, I need to scan the advertising data of my peripheral wich advertise with extended advertsing and LE coded PHY.
I use zephyr 3.7, and I work if I use the BLE controller...
Using Modem FW 1.3.6. Using NCS 2.6.0.
We're experiencing an issue in a test setup where we are getting this error reported (528) when trying to clear/set root certificates...
Hello nRF Team,
I am developing a ble terminal app based on the Bluetooth: Peripheral UART sample (nRF Connect SDKv2.7.0) on nRF52840DK. I was testing the app BLE pairing...
When following the unit test example, and even with an alternate minimal implementation, I get the following error:
PS {nRF Connect terminal} > west build -b nrf52840dk...
To people who might be interested in this ticket
I'm trying to make a WiFi connection using the nRF7002 chip. It is a custom board based on STM32 chip. My question is, is...
example:ble_app_uart+ esb_timeslot SDK17.1 Hi Recently our product (PRX) received poor esb communication. I caught through sniffer that when PTX sends a message, our device...
Hi, I have gone through Lesson 4 in Wifi fundamentals. But exercise 1 fails to compile. I have also tested to compile the solution-project, but with the same result. There...
When I look at eh graphic .overlay, I see that the UART0 is there, but no node is assigned. Is there a Node for a two wire UART Driver with no flow control? Peripheral only...
Hello,
I bought a new USB keyboard and since i can't detect anymore Nordic Devboard as nRF5380. No device detected on Visual Studio Code, and on nRFProgrammer neither. ...
Hi,
I working on a project where i measure the distance between nrf52840 dongle and nrf52840 dk using multi carrier phase difference method.
Now, i want to display the...
Hello.
I'm currently trying to send AT Command using an external MCU or USB to UART to check LTE on the NRF9160. The board I use is the nRF9160DK. I changed the pins of...
HI,
I have two solar panes for my project 3W 5V and 2 W 9V. I would to measure current of the panels with the Power Profiler II.
I think this should work (my calc is 3W...
Good Evening!
We are designing a project using BLE; however, it requires quite heavy processing. We are still at a low level with pure C to save power, but the MCUs offered...
