Dear Nordic Experts, This one's a tough nut to crack:
The firmware is based on nRF5 SDK for Mesh 5.0.0 with nRF5 SDK 17.0.2 and Softdevice s132 7.3.0. It runs on a nRF52832...
SoC: nRF5340 SDK: nRF Connect SDK 1.9.1
CMAC calculation works fine with SDK 1.7 and SDK 1.8. But it failed with SDK 1.9.1.
psa_mac_sign_setup returns error = PSA_ERROR_NOT_PERMITTED...
Hi, I'm pretty new to microcontroller programming so please correct my wrongs.
I'm using the Libuarte driver library to have the pca10040 talk to my server via serial connection...
Hello,
Fllow the guide of Configuring and performing DFU over Mesh,I can update firmwre successful use DFU:
Source: Example/Dfu
Target: Blinky(about 180 segment)
But...
Hi, I am working on custom board with nrf9160. I want to use LTE LINK MONITOR but my uart don't work. I create simple helloworld application from samples. I change uart0 rx...
I am a beginner and I want to switch from SDK 17 to nRF connect SDK v2.6.0, but I found that many configurations are different, such as gap initialization, gatt initialization...
Hi,
In my wearable application, I would like to have reset functionality by pressing two buttons, which I also would like to use as application interrupts. I read that the...
I'm working on implementing asynchronous UART on a nRF52840dk but uart_callback_set() is returning -88 (ENOSYS), which according to the tutorial here means it's not supported...
Hello!
I am using a nRF52840 board for some really simple development. First I just tried to run the blinky example and connected with another BT device. It worked well...
I attempted to use https://github.com/Protocentral/protocentral_max30001_zephyr_driver to build my project. However, I am still encountering some issues.
1.In the overlay...
Was following steps here to set up the sidewalk sdk from a blank nRF Connect SDK for VS Code application template using sdk v2.7.0. I noticed immediately that the directory...
Description : I am experiencing a build issue after porting my project from nRF SDK 2.4.2 to nRF SDK 2.7.0. The project involves using the nRF5340 and was building successfully...
Hi,
I'm trying to implement an application that acquires data from two channels of the SAADC in "parallel". I'm currently using the nRF52 DK and nRF5 SDK v17.1.0. After...
when I change from compatible = "nordic,nrf-spi" ; to compatible = "nordic,nrf-spim" ;
the SPI transceive failed
my overlay file
my yaml file
main code
nrf52840 and nrf5340
NCS 2.4.1
I have a project based on the Thread coap_client with mcubbot added, and we are migrating it from the 52840 to the 5340. We need to maintain...
I am developing an MQTT client application with NRF9160, trying to connect to a Mosquitto broker using TLS with three certificates. However, I am encountering an SSL version...
Hi,
I encountered some problems when using UARTE.
In terms of hardware, I have connected the 52840DK LOOPBACK_PIN_1A and LOOPBACK_PIN_1B.
Software code is the original...
Hello,
I see that kiss_fft is used in the libLC3 library. I would like to use it for another part of my product in addition to the pre-compiled LC3 lib, but don't want to...
I'm pretty new to embedded development/electronics and I'm trying to interface with a I2C pressure sensor, but I can't seem to communicate with it. I'm using nrf52840dk board...
Hello,
Up until today I had been developing fine with visual studio code, installed via Toolchain Manager. Then, I clicked "Pristine Build" for the first time in a few days...
