Hello,
I have tried twice to request for SUPL license for getting A-GPS working but it has been denied both of the times. I think first time it got denied due to mismatch...
Hi Nordic Team,
The atomic fifo implementation is based on armv7-M, right now I want to port it into cortex-A processor, I made some changes to get it compiled without...
Hi,
Kit:nrf5340
Can you please tell me if there is any example in nrf connect SDK v1.5.0 related to data transfer concepts.
Is ble controller will be enabled during...
I'm was testing the gsp sample in samples/nrf9160/gps. It runs fine on my nRF9160DK and reports NMEA messages. However, when i ran it on my custom board, it failed in setup_modem...
Hi,
I'm attempting to obtain sensor values for a project to be completed less than a week from now and I have not yet started programming so any help would be greatly appreciated...
Hi
I am using nrf52832,SDK version: SDK : RF5_SDK_17.0.2 .
USE CASE:We have two central and one peripheral.We need to control two central with one peripheral(REMOTE...
Hi all !!!
I am trying to program the bootloader and softdevice using the J-Flash software, but I get this error, how can I fix it?
Board: PCA10056 (NRF52840)
SDK: 17...
Hello,
I'm currently using the nrf9160 for a university project and I'm having problems with connecting my custom PCB with nrf9160 to nRF Cloud using the asset-tracker-v2...
Hello:
I want to ask you, we want to add our own custom data in the Ble scan response package, including Company ID,
we know Nordic's company Id is 0x59, can we change...
Hello,
I am trying to connect the nrf9160 dk with the SLM application to our STM32.
The idea is to use the nrf9160 modem to connect to NB-IoT/LTE-M and control the modem...
Hi there,
I compiled a QSPI test program on board nrf52840dk. The SDK version is 1.9.1. Everything works fine. I would like to upgrade with SDK 2.2.x but I have several...
Hi Nordic.
I am developing with nRF52832DK and SDK 17.1.0
And it's connected with my Qualcomm board.
I want check GPIO input interrupt and output settings.
But...
Is it possible to view RTT console outputs in vscode during a debug session? I would like to see RTT console outputs right from the start, e.g. from bootloader, preferably...
Hi,
While using LE Audio, would it be possible to choose the data rate from 125kbps, 500kbps, 1Mbps, or 2Mbps?
nRF52 series do not support 500k coded PHY, so I would...
Dear support,
In NCS 2.1.2, it looks like download_client.c:socket_recv() is returning an erroneous unsigned type size_t , considering that it can can return either -1 or...
Hi,
I have late start issue on advertisement.
I have two device mode and we switch between when we want to. Device starts with Mode_1 with BLE enable.
When I switch...
Hi DevZone,
I am working on an application using:
nRF52840
FreeRTOS v10.0.0.0
nRF SDK v17.1.0
S140 v7.2.0
My question is if it is possible to enable the S140...
Hi,
With the nRF5340 DK boards (PCA10095), there are 3 VCOM ports (as viewed in VS Code) - printk debug logs for the app core are transmitted on VCOM2. However, the nRF5340...
hello to all,
I need to insert two CAN ports on the spi3 port of the nrf52840 with two different chip select and interrupt.
I have created an overlay file that defines...
Hello,
We have completed our custom board with nRF52810 and nRf52832, as asked in earlier questions needed SWD and SWDIO pins to upload code in SoCs.
So could you suggest...
Hi,
I recently found that the 5340 has a slow startup time on my custom nRF5340 based hardware, it takes about 3 seconds from power-on to the Main code running.
I did...
