Hi, I'm pretty new to microcontroller programming so please correct my wrongs.
I'm using the Libuarte driver library to have the pca10040 talk to my server via serial connection...
Hello,
Fllow the guide of Configuring and performing DFU over Mesh,I can update firmwre successful use DFU:
Source: Example/Dfu
Target: Blinky(about 180 segment)
But...
Hi, I am working on custom board with nrf9160. I want to use LTE LINK MONITOR but my uart don't work. I create simple helloworld application from samples. I change uart0 rx...
I'm trying to add a second element to (light_switch\server) (SDK_for_Mesh_v5.0.0). I've already have a look at this post , it gives an idea but I found that it's not applicable...
Hi,
Again the topic which has already been discussed several times in this forum. I just want to share my experience and perhaps help other users having difficulties.
...
Hello,
in my device tree there are three nodes/items concerning battery Management:
One load enable pin
One measure enable pin
the required ADC configuration
...
Hi Team,
We are currently using nrf Connect SDK 1.8.0 and developing our application using nrf52833.
Currently we use our own git to maintain our application and nRF...
Hello, When enabling the Sensor system and having a qdec device enabled in my dts I get the following error:
This seems to be a bug with the Zephyr code checking a const...
Hi,I'm using nrf52832. I configured P0.20 as GPIO output,P0.22 as GPIO input.These two pins are connected wiht a 10Kohm resistor.I measured the voltage level on P0.22 is about...
Hello DevZone,
I'm using nRF5 SDK for Thread and Zigbee v4.2.0 and trying to test Zigbee OTA example.
I'm following this guide https://infocenter.nordicsemi.com/index...
Hi,
I am working on thingy91, I have created/added a BMS module in the project which gives different values for different data fields.
Everything is fine as BMS is transmitting...
Hi,
I am using TWI channel0 on my nRF52833 as master to get readings from a few sensors.
I need my nRF52833 to communicate with another microcontroller over TWI/I2C so...
I have code which works on the nRF52DK and on the Fanstel BT832 module, which does not work on our custom board with the CIAA package. Our custom board does not have an external...
Hello, we have a project in nRF Connect SDK, where we'd like to use a separate .conf file for b0n subimage in a multi-image build,
Let's say it's called b0n.conf. So, before...
Hi,
I would like to ask is there a dll file and header (.h) file for the nRF Connect Desktop Bluetooth Low Energy software? I am seeking for a chance to apply it in the...
Hi Good morning
Could you please to know the reccomendable dimentions of pad for soldering, dimentions of pad, PCB Layout for soldering component.
For example the component...
I was running Ubuntu 18.04 and Actinius Programmer was able to upload an example firmware without a problem. However, I upgraded my computer to Ubuntu 20.04 and Actinius Programmer...
I have used nrf5340 audio DK with nrf\applications\nrf5340_audio\bin\ble5-ctr-rpmsg_3251.hex in net core and zephyr\samples\bluetooth\hci_uart in app core directly after receiving...
Hello,
I want to install NCS 2.1.0, but I get the following problem.
I used toolchain manager 1.2.0 to install NCS 2.1.0. Open VS Code is now available.
I opened...
Hi,
I have a question, I use a 52840 board as the Bluetooth center. The protocol is S140. The other 51822 board is a Bluetooth peripheral. The protocol is S130. The routine...
