Hello, I have NRF D 24LU1P 1201FD and NRF F 24LU1P 2136IW. The first one executes all commands, while the second one does not work for writing and erasing. I tried to erase...
Hi! Could you clarify a bit about Bluetooth mesh gateways' implementations. I wonder to know possible ways of Bluetooth mesh gateway implementations. How is it possible right...
Hi everyone.
I catch a terrible issue
When I use nrf52840 and NUS Android app and had for a short time a bad rssi (because of long distance between Android and SoC) and...
Hello
We need to scan for more than 8 devices, so we can't use witelist directly.
We have an idea to use presaved IRK and mac-addresses and use scanning without witelist...
Dear Nordic,
Do we have ready-to-use keyboard driver with scanning/debouncing?
I've not found an example or docs about using KSCAN with gpio-connected keyboard...
I have one TX and another RX codes for data communication by ESB protocol. To verify whether data whitening can be enabled, I added below register setting on TX side only...
Hi. I'm developing nRF52832.
I'm in the process of setting up BLE, but there's a problem.
There was a problem while I was organizing the files due to successful BLE communication...
Hi,
I can able to get the DEVADDR0 and DEVADDR1. I am not able to make out How this EUI64 id is calculated using the DEVADDDR value.
I always get F4CE36 starting numbers...
Hi,
I'm running example mqttsn_sleepy_subscriber from nRF5_SDK_for_Thread_and_Zigbee_v4.1.0_32ce5f8 on a nRF52840-DK with RaspPi_OT_Border_Router_Demo_v4.1.0-1.alpha.img...
Hello Nordic Team,
I am trying to flash the existing BLE light example code in nRF connect sdk to my BL653 kit with Segger Embedded Studio. The node is not getting detected...
Hi.
I'm facing an issue following this guide ( https://devzone.nordicsemi.com/nordic/nrf-connect-sdk-guides/b/software/posts/using-a-custom-secure-partition-manager-wtih...
I am using running "ble_app_uart_c" example in my Central nrf52 DK board and ruuning "ble_app_uart" example in my peripheral nrf52 dk board..
IF I am sending ASCII values...
Hi,
I'm working on a multilink central device with SDK16, nRF52832.
I'm trying to connect the central to 2 peripherals with certain address. So I added 2 address filters...
Hi all,
I have a nRf52832 Buttonless DFU setup and application is BLE APP UART.
nRF52 SDK = 17.0.2
I need to send a hex file of STM32F4 through UART. Do you have any...
Hello
I'm using sdk17.0.2. And I'm using the ble_nus service with the addition of nrf_crypto (AES_CTR).
I originally used nrf52832 and pca10040 and the test went well...
I just got a new nrf9160DK rev 0.15.0. While plugged in to USB and the switch in the off position, my meter reports 4.95V and 0.016A. Why is this happening? My older rev 0...
From the product spec, the voltage accuracy is listed as -10, +5% from the programmed value. We're using 3.0 V. For our application I need some more specifics on this regulator...
Hi,
I'm building DFU secure_bootloader with oberon crypto library as mentioned here https://devzone.nordicsemi.com/nordic/short-range-guides/b/software-development-kit/posts...
Hi,
I'm developing an Android app using the nRF Mesh Library. I have a scenario in which a few phones need to be provisioners given that these will configure new nodes...
