Hi everyone.
I catch a terrible issue
When I use nrf52840 and NUS Android app and had for a short time a bad rssi (because of long distance between Android and SoC) and...
Hello
We need to scan for more than 8 devices, so we can't use witelist directly.
We have an idea to use presaved IRK and mac-addresses and use scanning without witelist...
Dear Nordic,
Do we have ready-to-use keyboard driver with scanning/debouncing?
I've not found an example or docs about using KSCAN with gpio-connected keyboard...
Dear Nordic Experts, This one's a tough nut to crack:
The firmware is based on nRF5 SDK for Mesh 5.0.0 with nRF5 SDK 17.0.2 and Softdevice s132 7.3.0. It runs on a nRF52832...
SoC: nRF5340 SDK: nRF Connect SDK 1.9.1
CMAC calculation works fine with SDK 1.7 and SDK 1.8. But it failed with SDK 1.9.1.
psa_mac_sign_setup returns error = PSA_ERROR_NOT_PERMITTED...
In my attempt of learning the nRF52 "eco system" (nRF52 DK, nRF15.3 SDK, SES and pca10040e project for nRF52810), I have combined the GATT_C, GPIO and SPI examples to make...
Device/SW Info:
Ubuntu 18.1 SDK : 15.0 SD 132 v 6.0
NRF52832 QFAAE1
The device once connected to the device is immediately dropping the connection upon going into...
Hi,
I am using a sniffer on nRF52840 DK between by central and peripheral device. The frequency of packet transfer is at 433MHz. Can the sniffer detect the packets at the...
Hi everybody,
I am currently trying to write in flash several records key in a same file using fds_write, fds_update, fds_records_find.
My page is FILE_ID = 0x1000 and...
Hi,
I have an application which scans for BLE advertisements and pushes some information about it over UART.
I run this on a nRF52840 DK card using softdevice s140 6.1...
Now, I have a project that needs to do a master device to communicate with another slave device, but the slave device is done by the customer. I found that my main device...
Hi,
When trying to connect various thingy's to an Android with the Thingy SDK, the debugger gives me that :
D/BluetoothGatt: onClientConnectionState() - status=8 clientIf...
Hello ! So i have a nrf52 device, and i would like to know if there is a possibility to us it as a multi hub devices. ie: two nrf52 devices, one programmed with ble_app_uart_c...
Hello Everyone,
I am building an application where I have to change the scan window (BEARER_SCAN_WINDOW_DEFAULT_MS) in run time, based on a specific event. Does the stack...
I cannot find any useful information on the purpose of this project: examples\connectivity\ble_connectivity\pca10040e\ser_s112_hci (and likewise with other boards & SoftDevices...
Hi all,
I have a hard time to merge Mesh Proxy Service and Nordic UART service. I am working with mesh SDK v. 3.1.0 and nRF5 SDK v. 15.2, coexistence example ble_app_uart_coexist...
I am considering using BLE advertising for sensor devices as peripherals and using a mobile phone as receiving device.
Because the number of sensor devices can be more than...
The current protocol for the mesh serial interface as documented here:
http://infocenter.nordicsemi.com/index.jsp?topic=%2Fcom.nordic.infocenter.sdk%2Fdita%2Fsdk%2Fmesh_sdk...
how to program an nrf51822 chip(chip with ou coin cell battery the rectangular chip not circular) using nrf51-DK to work as a beacon .. kindly share me the detail process...
using nRF52832, SDK 15.1, custom made units.
My Obervations - (in bootloader settings) $nrfutil settings display ota46to47.hex
when device is flashed "Current bank"...
