How to prevent storage partition from erase durning MCUBOOT firmware update?
I use Settings with NVS to store data
CONFIG_FLASH_MAP=y
CONFIG_FLASH=y
CONFIG_SETTINGS...
Hi,
I am building a Thread network ( www.youtube.com/watch with a Rasp Pi 4 as a border router, an nRF52840 DK as an RCP, and an nRF5340 DK as a child to be added into the...
We found a problem with a client's legacy design. They use two 12 pF load capacitors for the 32 MHz crystal, which has a 4 pF capacitance. This is a somewhat unusual Abracon...
Hello DevZone,
I have a project where I currently use the AT%XPOFWARN feature, in order to turn off the modem in case the battery voltage is too low. It's used in both cellular...
We use several Nordic chips in our BLE sensors. We bond to the devices from Android, connect to update configurations, then disconnect such that the device then advertises...
Dear Nordic DevZone,
I'm encountering pairing issues with mobile devices and a nRF54 DevKit flashed with HCI over UART firmware. After initial pairing, deleting the bonding...
Hi,
I have successfully connected an MCP3004 to the nRF52832 and can assign the ADC channel 0 output to a characteristic value. Works beautifully.
However, there are...
Hello,
I would like to know what are possibilities for low power in a central device on nRF52 chip.
I need to be in BLe connection mode, and be able to receive notification...
I'm trying to figure out if the NRF51822 is capable of performing the tasks I need for my project. I need to be able to do the following
4x PWM at ~2kHz
4x Analog read...
I am building a Bluetooth Mesh project and when trying to make a custom Makefile for the Mesh Light Control Example , but when compiling the project i get this error:
Compiling...
!!! (Distributor is unknown to me, but I can get it if needed)
Hello,
We are developing a BLE enabled device to operate on iOS and Android phones.
The nRF52832 chip...
Hi friends,
I'm using a NRF51 IC with this 4.0BLE Modul PTR5518 and i have big problems with Range. As a protocoll i use gazell.
In air it is possible do get some correct...
Hello,
I am currently trying to make an MSD RAM disk with nrf52840 nRF5_SDK_14.0.0 with O0 optimization level. And had no success. For some reason in Keil example O3 is...
Hello every one,
So after I made my 3rd party NRF52832 board and flashed softdevice S132 with arduin ide and ST link V2 I'd like to migrate to something more serious in...
Hi,
Do you know how to make the nodes in the Mesh send back the data to the main device?
For example, a node is a sensor that gets a new value and now needs to send the...
Would like to get continuous advertising data from a known device ID - without connecting. Would like to do this on a Windows PC. I don't see a way to do this with nRF Connect...
Hello,
We are working with the one potential customer . they are working on battery connected beacon project below are the some queries
customer using nrf51822...
i am compiling an code just to store a data to flash and retrieve it. i wrote the code for that i included fstorage.h,section_vars.h and added fstorage.c. I am not using any...
Hi,
In nRF5 SDK v14, in the file ble_advdata.h, there is a routine to create advertisement data from a ble_advdata_t struct that is passed. This struct allows only 1 manufacturer...
This omission leads to linker errors:
_build/app/nrf_ble_gatts_c.c.o: In function `nrf_ble_gatts_c_on_db_disc_evt':
nRF5_SDK/components/ble/ble_services/experimental_gatts_c...
