Hello, I'm working with the EK PCA10003, that has the NRF51422. I'm trying to read the information of the accelerometer MPU6000 with an ISP interface. At the moment I cannot...
I'd like to use the GATT/GAP driver from an ARM based Linux system. Is there any possibility of getting a library compiled for ARM or (cough) the source code to build it myself...
It is possible to run easily a SoftDevice stack (e.g. S110) on nRF51422 using an accurate 16MHz external clock reference for HFCLK instead of an external 16 MHz crystal oscillator...
I want to change data bytes in the advertisement packet. In ACI_DEVICE_STANDBY I put: lib_aci_open_adv_pipe(1);
In ACI_EVT_CMD_RSP: I get feedback that command 1B (I assume...
first,PCA10005 can't load sofeware hex that after s110 7.0.0 hex(include 7.0.0),and gostudio note that the given hex file can not open successfully.
second,the PCA10005...
Hi there,
I want to manage certain devices that have an address and a value. I would like to dynamically add and remove devices from my data structure. I believe that using...
nRF52840-Preview-DK LED5 is off, J-Link Error.
I press IF BOOT/RESET key then poweron the PDK, no BOOTLOADER removable disk drive letter appears, I have installed the driver...
Hi all,
I am developing a sidewlk application as a replacement for LoRaWAN recently based on the sidewalk protocol implemented in the nRF connect SDK. I would like to check...
Hello,
We are currently manufacturing products using the nRF52840 with the nRF5 SDK. We are planning to develop new products using the nRF Connect SDK and are currently...
below is my develop environment .
TOOL : VSC - NRF CONNECT SDK 2.6.99 DEV : NRF7002DK
I am currently looking into the BLE GATT structure in NCS.
Since I need to use...
1. am currently using the nrf9161_dk. and have not modified the modem FW in anyway.
2. I am using the vscode extension provided by nordic to build/run this sample
a, i...
Hello, I am trying to migrate from v2.5.0 to v2.6.0. I had subghz working for the sidewalk samples in v2.5.0 but can't seem to get it working in v2.6.0. I don't see any errors...
Dear Nordic DevZone community,
I am currently grappling with a challenge involving the transmission of data from an NRF52 device to the NRF Toolbox app through BLE.
To...
When I build some example (e.g. samples\bluetooth\direct_test_mode) with NRF Connect SDK Toolchain v2.6.0 and NRF Connect SDK v2.6.0, I get the following errors: warning:...
Development is proceeding with VSCode.
We are developing the source by adding an overlay file to the nRF5340 Audio sample source.
If you copy the entire folder, open the...
I am quite new to the nRF SDK. When setting up an nRF project in VSCode, I can build my project but I cannot flash the target.
My target in this case is an nRF52840-DK....
We have unit testing working with the Zephyr Unity/CMock setup, however the test runner (test_runner_generate) ignores preprocessor directives (#ifdef) and removes them when...
I have an application that must manage different ble connection with different device (and so different UUID services). For the scanning and connection I used the bt_scan_filter_add...
I am using a ble+wifi module which is MS12SF1 which has nrf5340+nrf7002. It is connected with a pcb in which there are 2 inmp621 pdm microphones. I have tried integrating...
I have a dongle attached to my Windows PC and it has the nRF Sniffer firmware flashed onto it. I have also installed the nRF Sniffer extension for Wireshark.
When I start...
