I want to change data bytes in the advertisement packet. In ACI_DEVICE_STANDBY I put: lib_aci_open_adv_pipe(1);
In ACI_EVT_CMD_RSP: I get feedback that command 1B (I assume...
first,PCA10005 can't load sofeware hex that after s110 7.0.0 hex(include 7.0.0),and gostudio note that the given hex file can not open successfully.
second,the PCA10005...
Hello! I'm using sdk8 and s110. I want my peripheral device to send data to the central. I doing following steps:
1. initialize service:
void services_init(void)
{...
I am glad that I have successfully used the library from www.libstock.com/.../nordic-semi-nrf24l01-example in a pair of PIC18F45k50 devices. One is acting as a Tx and another...
Hello.
I have had a search but can not find anything so sorry if this has been covered before.
Our company has developed a consumer product using the nRF51822-QFAA-R7...
Hi every one !
I am trying to get working a code that it was working "Ok" 2 years ago.
Currently, I cannot get communication between both breakout boards.
To simplify...
Hi
I'm trying to add to my Linux board (RPI4 CM) a cellular connectivity and I thought about using nRF9160 SiP because it's a product I've already used and it's low cost...
Hi
Spotify 128 kbps aac stream is about 16 bytes per ms. Ble should support 31 bytes per packet.
So can I stream 16 bytes ms over lte m to nrf 9160 then via uart to...
Good morning!
I hope you will forgive my trivial question but I am a beginner. I don't quite understand the partition structure presented in the "NVS" example. Using the...
Hi,
A veteran of nRF5 SDK but new to NCS.
I tried to run tx_rx_non_blocking example from the latest (2.6.1) NCS SDK, but can't get it to run (nR52840DK)
It seem...
Hello, I recently set up an nRF52840 with the nRF7002 evaluation kit using the WiFi station sample. However, during the build process, I noticed that it consumes a significant...
Hi,
I'm integrating an external SPI flash W25Q32 with the nRF52840 using the NOR FLASH driver, but it's not functioning properly as the MCU log indicates an MPU error. ...
Hi Team,
I have 1 nRF5340 Audio DK. With the steps mentioned in below links, I configured Json file to Headset and I'm able to achieve it. ( developer.nordicsemi.com/.....
Hi All!
I have a question, i am using nrf52833Dk as an extended advertiser and nrf52840 dongle / 2nd nrf52833Dk as a scanner using the BLE desktop App (nrf connect for desktop...
I am not able to send 25 array packets each second. array size is 244 bytes I am reading the sensor data continuosly and every 40 ms i am sending the data to bluetooth using...
Hello,
I am on a development team utilizing Nordic Board NRF52DK to connect to a custom NRF52832-based board/external device via debug out on the Nordic Board NRF52DK, the...
Hi,
I'm experimenting with an Acconeer XM126 board which has an nRF52840 processor (and an Acconeer A121 chip) and a Bluetooth antenna (and an RF antenna too). I'm deploying...
Hi all.
I have made myself a board which has a module with the nRF52833 chip embedded onto it. It's effectively a board with a set of switching regulators on it to drive...
I am using NRF52833 and trying to setup DFU specifically for OTA.
As experienced in other threads the size limitations are there
Secure_Boot builds creating slot partitions...
Howdy guys,
I am using an nrf52840 and SDK version 17.1.0 alongside Keil. I just upgraded from using the arm compiler version 5 to 6, which required me to switch from the...
Hi,
I have an implementation in which two boards communicates through ble and i want to measure the throughput of both. The behaviour that I see is that increasing the connection...
