Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Hello everyone,
I got a task which I try to implement using a NRF51822 iBeacon board.
The Task:
Advertise a Device and provide a mechanism to connect without traditional...
Hello, I'm working with the EK PCA10003, that has the NRF51422. I'm trying to read the information of the accelerometer MPU6000 with an ISP interface. At the moment I cannot...
I'd like to use the GATT/GAP driver from an ARM based Linux system. Is there any possibility of getting a library compiled for ARM or (cough) the source code to build it myself...
Hi Nordic,
1. I am planning to do DFU update with UART
2. I Build smp_svr and flashed successfully when am using mcumgr its getting NMP Timeout
3. I added CONFIG_MCUMGR_SMP_UART...
Hello,
In my project, I have a device (nrf52833 custom board) which I want to operate in dual role (central/peripheral). I've followed a ble_app_hrs_rscs_relay example...
Dear Sir/Madam,
We developeted a smart device based on nRF52840 chipset(to be more accuracy, we desgined our own module based on this chipset, then our end product use the...
I'm currently trying to change the host name of "https_client" and check the operation, but it doesn't work.
Even after changing the host name back to the original, "Waiting...
Hi,
We want to do provisioning of multiple mesh nodes using pb-adv procedure. we installed nrf MESH app, but we are not able to do provisioning for one node using Pb-adv...
Hello everybody. I'm designing a custom PCB fed by a typical 3.7 V nominal 4.2 V peak lipo battery, where minimal area and thus component count is a key factor. Aside from...
How can I adjust the BLE transmit (Tx) power, up to and including +8 dBm? I'm using nRF Connect SDK (NCS) on an nRF52840-DK .
I modified the throughput sample to reverse...
Hello, I'm trying to run the Ble Peripheral sample from "nrf\samples\bluetooth\peripheral_lbs" i'm using nrf connect V1.8.0 and NRF5340dk i followed the code in the github...
Hi,
I'am using the Ultrasonic Oxygen Senor with the nrf5340, the output is like this "photo" I want to calculate the concentration and the purity and with this values I...
Hello,
Is there any way to program the frequency output when sending a carrier wave to have a step size of around 1KHz? It seems that the default step is 1MHz.
Hi
I am trying to get the manufacturer data by ble_advdata_parse() as instructed in this case and this case , but it's not found in my SDK14.2, so how can I get the manufacture...
It's not possible to proceed a firmware update of matter light switch example on nRF5340DK.
I use following SDKs / Repos
nrfConnect SDK v2.0.2
standalone zephyr SDK...
Hello,
I have a component (AMC1306) in which I input a signal of at least 5Mhz. When this signal is triggered to this component, it sends me back data at this same speed...
Hi, I am trying with coap_client/server example programs on a custom board. I created a custom board for Zephyr and it is compiled without errors. I have a single button switch...
