Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Hello everyone,
I got a task which I try to implement using a NRF51822 iBeacon board.
The Task:
Advertise a Device and provide a mechanism to connect without traditional...
Hello, I'm working with the EK PCA10003, that has the NRF51422. I'm trying to read the information of the accelerometer MPU6000 with an ISP interface. At the moment I cannot...
I try to run Azure_IOT_Hub without HUB. I have set in prj.conf and prj_qemu_86.conf:
CONFIG_AZURE_IOT_HUB_DEVICE_ID= "mydeviceID"
CONFIG_AZURE_IOT_HUB_HOSTNAME="mydeviceIOTHub...
Hello,
NCS1.9.1,nRF5340DK,Windows10 X64,VSCode,
why frequent problems of "west flash --recover",
some time run cmd " west flash --recover",it will be ok,
and some...
Hi,
I'm trying to wrap my head around doing some basic GPIO reading, writing etc. and hopefully some interrupts. Apologies if these are basic questions - I've only really...
Hello dear People,
I would be very happy if anyone has an idea how to solve this.
The Problem is the following: I am using nordics lte link controller to connect to nb...
Hi,
1.) I am programming a custom board based on NRF52833 using NRF52833-DK using SWIO/SWCLK interfaces using Segger Embedded Studio with NCS v1.6.1. I am trying to print...
1. Your documents mention only SPI3 and SPI4 are available in non- secure mode.. which means spi-0,1,2 should not be available in non-secure mode.. But if i use nrfx drivers...
Hello.
It is under development using nrf52832 (S132 v7.0.1, SDK v17.0.0) as a peripheral device.
I'm currently considering Flash Data Storage (FDS).
As settings, "FDS_VIRTUAL_PAGES...
Hello.
Target nRF52832( nrf52dk_nrf52832)
SDK NCS v1.9.1
Build : SES for win 10 (5.68)
1. Support BT5.3
My project used nRF5_SDK_17.1.0_ddde560. Recently I found...
I am using a custom board design with a Nordic nRF52832 and have implemented the Nordic time sync algorithm outlined here ( https://github.com/nordic-auko/nRF5-ble-timesync...
Hi everyone,
I'm currently using nRF52832 with nRF5DK_V17.1.0 file.
I understand that this question has been risen up quite a lot however, I still do not understand why...
Hello Nordic team,
I am testing a timer using code snippet which Nordic team recommended as a reference. My code is something like this:
uint64_t start, stop;...
Hello,
A nrf52840 central device programmed with Soft-Device S132 and connectivity firmware, the host is interfaced via USB and uses PC-BLE driver API's to communicate with...
Hi,
I'm using nrf52840 DK and android based mobile with nrf connect for mobile app installed.
I would like to execute a freestanding sample code to transfer message between...
Hi Nordic,
I met a issue on BUS FAULT , which caused by queue.
It core dumps that:
[2022-03-22 15:35:12.657] [xxx]index = 6,len = 158 [2022-03-22 15:35:12.660] [xxx...
