We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
The newest version that will run on my mac is 3.8. any never version will just freece at the startup window.
...but the programing app crashes when I try to add a file in...
Hi,
I am using the RSA sample code and I need to make the key persist. When I try to change the lifetime attribute to PSA_KEY_LIFETIME_PERSISTENT, the key generation fails...
Hi, I am developing a device using the nRF52832 mcu. I have written my application and have interfaced with an external I2C Sensor. It works perfectly on the NRF52-DK, I get...
I am using NCS v1.9.1 with the nRF52840 and I am not able to move the MCUBoot secondary slot to SPI flash.
I have been able to communicate with the device over the SPI...
Hello,
The nrfjprog command is used for the nrf51822 / nrf52833 program.
Suddenly, nrf52833 shows the following error.
Even though family is specified, it is the same...
Hi,
I'm working on NRF52840 DK , S140 and I'm trying to send large data (around ~64KBytes) from a peripheral device. I'm using the following functions: - sd_ble_gatts_hvx...
Hi Everyone,
I'm currently testing the battery service with my development kit, nrF52dk, and I've found an error stating "The handle is invalid" when I press the "read"...
Hi,
I want to build a wireless split keyboard (Left and right parts). I want them to connect to one PC but only need to establish the connection one time. Can both part...
I am working on ble mesh with sdk17.0 and sdk5 for mesh I want to send large data vai ble mesh I followed this post https://devzone.nordicsemi.com/f/nordic-q-a/71105/sending...
Hello.
I've a ublox module with nRF52811 chip.
Is it possible to make a BLE beacon receiver with nRF52811? If yes, is there any demo application? I've searched nRF SDK...
I have been playing with an Ikea Tradfri E1812 button, a Philips Hue bulb, and zigbee2mqtt. I see that when I bind the button's OnOff output cluster to the bulb's OnOff input...
Hello,
I am looking into evaluating the nrf5340 with different functions running out of external flash, and how current draw is affected by these functions. We are looking...
Hi All,
I am working on NRF52840 and trying to optimize the BLE throughput. The current settings are:
PHY: 2M PHY
Conncetion Interval: 9.375 ~ 15 ms
GAP_DATA_LENGTH...
Hi Everyone,
I hope you all are well.
I'm using nrf Connect SDK v1.7.0 and VS code for nrf52833 chipset.
So far I've used NUS service in my code to transmit some data...
Hi, I am trying to write an "event dispatcher" so it's possible to listen to types of event and send events. You pass a function pointer and it will be called when that event...
