Hi, I'm using the nRF8001 in an application that requires security so bonds to the remote client/central. My device supports firmware upgrades that may involve new nRF8001...
Hello.
Initially when reading the Gazell documentation I didn't think it'd be a problem but now in Keil seeing this has introduced some doubt whether it's a thing:
...
We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
HI Team
We are using nrf52832 in our one project. we just want to know the power down state. how we will put the nrf in power down and what actually happens in nrf when...
We have a design where 9160 is always battery powered (, and only the RESET-pin is the way we have to shut it down (keep in reset).
Probably this design might not be the...
i am using SD S140.
i have a 300us period that must take 300us, no more, no less.
for this reason i must call __disable_irq().
when i do it i sometimes get app_error_fault_handler...
I have done a program with keil IDE and am putting into use an ST link v2 for a debugger, and in Keil am getting “internal command error” as the problem.
The screenshot...
Hello,
We are developing hardware with a soldered down eSIM. Our previous LTE module vendor recommended 47pF capacitors on all the signal lines (CLK, RST, I/O) and 47pF...
Hi team,
I understand that it may not be a simple answer, but not sure if we have any clue on the support?
Based on the Devzone ticket: https://devzone.nordicsemi.com...
Hi there,
Recently, we used the nrf52833-DK to develope the direction finding.
We want to add an external antenna array we designed on the nrf52833-DK for AoA receiver...
I have a local carrier SIM card and iBASIS SIM card that came with the nRF9160-DK. LTE-M is activated on the SIM card of the local telecom operator. However, none of these...
Hi, I developed a BLE and Zigbee custom product, starting from nRF5 SDK for Thread and Zigbee v3.2.0. On BLE side, my customer ask me to have the BLE MAC number also inside...
Hello Nordic Support,
I started with a sensor sample project for ADXL362 Three Axis Accelerometer ( https://github.com/zephyrproject-rtos/zephyr/tree/main/samples/sensor...
Hello,
I am using PCA10040 DK for programming my custom board which is having the NRF52832 controller. Until yesterday afternoon, I was able to program my board using NRFgoStudio...
Hello. An LED is connected to the pin of my nRF52832 through a resistor to ground. How can you programmatically determine its presence? I tried to do pullup and read the port...
Hi,
For the first time iOS App interface with BLE device. But after killing and re-opening of iOS App connection not established. Can anyone share me the code from iOS App...
Hello,
I would like to know wich step I forget to do to send more than 20 bytes in NRF Connect app to a BL652. I followed some talks and subjects about it but it's doesn...
I am using ble_app_uart_c example to scan nrf beacons. Facing strange issue with debugger.
Enabled RTT and disable UART Logs, when i connect debugger and put break point...
