Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Hello everyone,
I got a task which I try to implement using a NRF51822 iBeacon board.
The Task:
Advertise a Device and provide a mechanism to connect without traditional...
Hello, I'm working with the EK PCA10003, that has the NRF51422. I'm trying to read the information of the accelerometer MPU6000 with an ISP interface. At the moment I cannot...
I'd like to use the GATT/GAP driver from an ARM based Linux system. Is there any possibility of getting a library compiled for ARM or (cough) the source code to build it myself...
Hello,
My config: - nRF SDK v17.1.0 - nRF SoftDevice S140 7.2.0 - FreeRTOS Kernel v10.0.0 (Amazon.com)
My project used BLE connection with custom service (based on NUS...
I want to use dynamic memory allocation. After searching these forums, I see the following options:
malloc
k_malloc
nrf_malloc
balloc
I haven't had success with...
Hello everyone I hope you all had a good start to the week. I am stuck with an issue I don't quite get. I wrote code with BLE, FreeRTOS, and GPIOTE as a "proof of concept...
Hi,
I'm evaluating the NCS peripheral_uart example for our needs.
I have an issue with deploying this example to an PCA10040 board. While running the example built for...
Hi All!
I have a problem which i can't really understood. I'm using nRF5340-DK evaluation board, and currently i'm trying to get one of timer (TIMER1 in this example)...
Hello,
I have a Nordic connected to a STM32. The DFU procedure on the Nordic works fine and I am able to upload and run a new firmware in buttonless mode. The Nordic also...
nPM1100 use JEITA profile that has charging range 0-60gc. Most batteries has charging range 0-45gc. Is it possible to limit charging to 0-45gc with this chip, or is JEITA...
Hi,
I am developing a product using the SoftDevcie s140 and SDK 17.0.2.
I have the problem, that the standard FreeRTOS port defines configTICK_SOURCE to FREERTOS_USE_RTC...
Hi,
I have a nrf52832 dk(pca10040 1.2.1), use gpio P0.29, P0.30, P0.31 to connect some external device,
external device working voltage is maximum 2.2v, so I connect external...
While running UART rx and tx calls the uart_callback_set I have set during initialization will stop running. This prevents me from sending or receiving any new UART information...
Hello,
Could you tell me if SoftDevice V7.3.0 can be used in SDK 17.0.2?
According to the following website, you should use Softdevice V7.2.0 in SDK 17.0.2.
https...
Hi,
I use a pca10056 with the "mqttsn_sleepy_publisher" example. Unfortunately, I cant connect to the mqttsn gateway. It throws me:
"NRF_LOG_ERROR("CONNECT message could...
Hi,
I am trying to perform buttonless DFU on my NRF52840 DK. I am using SDK 15.30. I performed following steps for DFU.
1. I flashed softdevice S140 6.1.1 using nrf connect...
