We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Dear Nordic,
I'm using the nRF connect app for the smart phone to test BLE bonding.
I hope to know the bonding feature on the nRF connect app is working with Random...
Hi.
We've created a custom board, and it works nicely.
However, when I try to build another application for this new board (i.e. "Add Build Configuration"), the new board...
Hi,
I'm using the nRF Connect app on android to DFU my devices.
On some occasions, after doing DFU and unbonding, the phone will keep asking if I want to pair the device...
The Absolute Maximum rating of I/O pin voltage for VI/O, VDD ≤3.6 V is -0.3V to VDD + 0.3V in Table 185. We would like to monitor the battery voltage using an AIN pin because...
Hi, We are using the SDK v17.1.0 and SD S140 v7.2.0. In our application we have to send only 1 advertising packet with updated data every 300ms and in some cases every 50ms...
Hi,
I work with win10 laptop, Toolchain nrf Connect SDK 1.6.1 on a nrf5340dk.
I modifyed peripheral_uart to use 240 bytes like it's explain into "ncs 1.6.1 peripheral_uart...
Hi, I am trying to create a custom BLE service.
Following is the main code:
These are my BLE write functions:
My sdk_config file says MAX_MTU is defined 23
...
Hello everyone,
I have a few questions related to NFC in nrf52832.
1. UUID in nrf52832 NFC is Unique?
2. Can I use nrf52832 NFC for payment purposes..? if yes How I...
Hello sir,
I am using nrf52832 soc with customised board want to use as UART pins as RX pins as 23 and TX pins as 24 .Is it possible to use the RX pins as 23 and Tx pins...
Hello,
I am trying to configure a Zigbee coordinator as done in the CLI example (for example 'bdb role zc' and 'bdb start') to get data from the multi sensor example,...
Hello,
Lately we've had some problems with DFU using the NRF connect app.
The device we are using is a nrf52832 running Zephyr 2.6 with MCUBoot 1.8
When we set the following...
Hi,
Turning on A-GPS (using the SUPL library) causes our application to encounter a boot panic ("unable to find bootable image"). Similarly, running the nRF9160 GPS example...
Hi Dev team,
I have been working with the MQTT example and building up my application. I establish a successful connection with the broker and everything runs fine for 5...
